0
1984 ford ranger just had the clutch replaced when you got it back the starter sounds like they left a tool in there you have battled with the repair shop since you have been through 3 starters since?
Bigbear
it may be that your flywheel is loose, and the starter is jumping the teeth,
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
1971 350 camaro i have gone through 6 starters and have replaced the flywheel still going through starters can you help?
if the engine has high comprshen it will eat starters
I replaced starter 6 times in 6 month period and have replaced the flywheel I am still going through starters I have a 1971 350 camaroNoone can figure out why this is happening Can you help?
If you have headers put a heat shield over the starter. That is what fixed my 84 C-10 starter issues. If it is a gear alignment problem try shimming. If it is a electrical problem try the heat shield.
How do you get all of the starters in Pokemon Emerald without cheats?
Either through the wi-fi center in jubilife center or trade one of the starters to another DS then restart your game and get a different starter and repeat. So start>get starter>trade>restart>starter>trade> restart get last starter and re-trade starters back. It's complicated and long but worth it.
Where is the ground wire on your starter to your Dodge truck I tried to tighten the starter and I accidentally touched the ratchet to the manifold and it sparked does that mean starter not grounded we?
Most starters are grounded through their mounting bolts and contact with the engine. Some starters have a braided ground cable between the starter and engine or frame. The arcing occurred because you shorted between an electrically "hot" connection and ground , i.e. the manifold.
What makes your 1993 ford explorer eat the starter you went through two starters in the last two weeks?
u need a new ring gear or fly wheel and a nother starter!!! your starter might be staying ingaged in the motor while the motor is running? in this case replace the starter solidoid
Starter makes grinding noise after engine is warm but if the remote start is used there is no noise is this due to a relay through the ignition switch?
The starter should only be making noise if you attempt to start the car and the starter is going bad. It is possible that the remote starter is bypassing the mechanical starter. Starters are very easy to replace. Be sure to disconnect the car battery before doing so.
1971 camaro 350 automatic transmission i have replaced the flywheel and gone through 6 starters no one can figure out problem can you help?
bad ground wire or not enough ground
Why did a 1996 VW Jetta 2.0 burn through a new starter solenoid 4 days after being replaced?
In my 97 Jetta, the key does not spring completely back from the start position to the run position by itself.I figured it out after burning through one starter motor.
What is the strongest starter?
Statistically, Charmander is the strongest starter Pokemon to take. However Bulbasaur will get you through the first two gyms easily, whilst Squirtle has the best resistance to your Rival's choice. All three starters are valid choices however, and it is easy to compensate for their weaknesses with your catches later on.
How do you replace the starter in a Jeep Cherokee?
Most starters have two mounting bolts and one thick wire (usually around 10mm or more) which goes to the starter relay and from there to the "+" side of the battery.The starter circuit is completed through the starter's mounting bolts - which are screwed onto the engine - and from there to the "-" side of the battery.Depending on the vehicle make and model, the starter relay is activated when the ignition key is turned to the "Start" position or when a separate "Start button" is pressed.
1995 Dakota won't start battery good starter good will push start can arch the strater and will start and run replaced ignition switch still nothing?
might be starter relay, or the crank circuitry from the switch or to the starter from the relay. I would trace back from the starter to the starter relay back through the neutral safety switch to the ignition switch.
Who battled on World War 2?
john Glenn, and president FDR led us through it.
