0
The belts themselves are not tightened but the Pulleys that the belts run can be "tightened" to stretch an aging belt so that it does not squeak, not all pulleys can be tightened. If you live in a warmer climate it is probably your AC belt. If you have a ka24-e (four cylinder engine) your compressor is on the bottom end of your engine, better accessed from underneath truck. on the outside of the belt pulley there should be a bolt attached at two points on a bracket, one point is where the head of the bolt is the other is near the center of the pulley, this is where the bolt grips. tighten the bolt with a PROPER METRIC wrench. the pulley should move towards the head of the bolt, it wont move much but you should be able to notice how much tighter the belt is now. DO NOT OVER TIGHTEN you will bend the bracket. tighten a little bit and see if the belt still squeaks, rev the engine up a bit. you can only do this so much before the belt will simply need to be replaced, if you see any cracks or wires coming from the belt you need to replace it!
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is the difference between a 1993 Nissan hardbody pickup truck and a 1993 Nissan d21 pickup truck?
they are the same truck,look em up at autozone.com,youll see what i am saying. D21 is the Official Nissan Designation of the Truck. Hardbody is the "Nickname"
My 1990 Nissan hardbody won't start battery is fine What gives?
its probbaly the starter. i have a 1993 and mine went bad. check all the wires and tighten everything that's loose and if that dosent work put a screw driver across the terminals on the starter and if it dosent turn over then the starter is bad
Show the location of water pump in 1993 Nissan Altima?
ON THE END OF THE MOTOR WHERE THE BELTS ARE....BEHIND THE COVERING FOR THE TIMING BELT.
How do you tighten the belts on a 1993 Dodge Caravan?
you dont belt is self adjusting one of the puleys is called a tenteder belt or tenteder may need repacleing
How do you replace a compressor belt on a 4 cylinder engine for a 1993 Nissan altima GXE?
jack up the passenger side of the car. remove the splash guard in side the wheel well (all the black plastic inside fender)and remove the tire then u can acsess the belts. there are 3 sperate belts with non automatic idler pullys. loosen the idler pullys of the belts until u get to the compresser belt. replace then reinstall and tighten the belts with the idler pullys to repair manuel specs. a special tool will be required to get the correct tension of the belts
How do you tighten the serpentine belt on a 1993 Asuna?
if a serpentine belt is loose, it needs replacing. there is an automatic tension pulley on all serpentine belts. so just buy a new belt and install
How do you adjust 1993 Nissan Micra handbrake?
Put the handbrake on and lift the rubber flap up just below the lever. Beneath that will be a 10mm nut, tighten that to adjust handbrake. 1993 micra should be about 5-7 clicks
Does a1993 300zx has a interference engine?
( YES ) according to the Gates website ( they make timing belts etcetera ) the 3.0 liter V6 engine in a 1993 Nissan 300 ZX ( IS AN INTERFERENCE ENGINE )
What are the fan belts for on a 1993 Nissan Serena van?
First of all, they are the same as the fan belts on any other car. The fan belt(s) are the serpentine drive belt(s) that turn your fan and other accessories (like alternator, compressor, power steering) They are often referred to as serpentine belts, drive belts, and accessory drive belts. The are located on the outside of your engine, driven by the main pulley (crankshaft pulley). R. Mesyef
Where is the clutch fluid on a 1993 Nissan pickup truck?
Where is the clutch fluid on 1993 nissan pickup truck.
When was Nissan Altima created?
Nissan Altima was created in 1993.
When was Nissan Quest created?
Nissan Quest was created in 1993.
