answersLogoWhite

0


Best Answer

In your case, it is most likely a failing Mass Air Flow (MAF) sensor. Scan for DTCs and check if you have a code that indicates a low input signal to the MAF. If so, that is the problem. Otherwise, you can also investigate replacing the brake switch, as described below.

Make : Volkswagen Model : JETTA Year : 2002 Build Dates : 20001001 - 20041130 NHTSA CAMPAIGN ID Number : 07V063000 Date Owner's Notified: 20070427 Date Received by ODI: 20070220 Date Added to Databse:20070221 Manufacturer's Involved: VOLKSWAGEN OF AMERICA, INC Manufacturer's Responsible for the Recall: VOLKSWAGEN OF AMERICA, INC Manufacturer Campaign Number: N4 Component: EXTERIOR LIGHTING:BRAKE LIGHTS:SWITCH Potential Number Of Units Affected : 1002000 Summary:

ON CERTAIN PASSENGER, WAGON, AND CONVERTIBLE VEHICLES EQUIPPED WITH OR WITHOUT CRUISE CONTROL, A BRAKE LIGHT SWITCH MAY MALFUNCTION IF IT WAS INSTALLED INCORRECTLY. Consequence:

THE BRAKE LIGHTS COULD BECOME INOPERATIVE, OR REMAIN ON. FAILURE TO PROVIDE THE PROPER SIGNAL WHEN BRAKING COULD LEAD TO A CRASH WITHOUT WARNING. Remedy:

DEALERS WILL INSTALL THE NEWLY DESIGNED BRAKE LIGHT SWITCH FREE OF CHARGE. THE RECALL BEGAN ON APRIL 27, 2007, AND WILL BE CONDUCTED IN SEVERAL STAGGERED MAILINGS THROUGH SEPTEMBER 21, 2007. VEHICLES WITHIN THE MAKE, MODEL, AND MODEL YEAR OF THIS POPULATION MAY BE INVOLVED IN EITHER THIS RECALL OR 06V-183, BUT NOT BOTH. THE REMEDY IS THE SAME FOR EACH RECALL. VOLKSWAGEN DEALERS WILL APPLY THE REMEDY BASED ON THE VIN NUMBER OF THE VEHICLE. OWNERS MAY CONTACT VW AT 1-800-822-8987. Report Initiator: MFR Vehicles Report Regulation Part Number: Federal Motor Vehicle Safety Standard Number: Notes:

CUSTOMERS CAN ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATIONS AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: 2002 Volkswagen Jetta 1.8T ASR lights and runs as if brake is engaging 4th time 3mos ago restarting engine switches it off but lately check engine light also comes on together with asr?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Relationship between a bridge and a switch?

Switches connect computers directly together while bridges connect switches, router etc together


When two parties work together to advance common ideas they are engaging in?

bipartisanship


What are the two conductors that connect 3 way switches together called?

The two wires that travel between two three way switches are called travelers.


What is a result of connecting two or more switches together?

The size of the broadcast domain is increased


Why does series circuits do the same as AND gates?

The output of an AND gate is set only when all of its inputs are set, and when switches are wired together in series, current can flow only when all of the switches are on.


What is core switch?

A core switch is one that ties all the communication together. A switch allows computers to connect together. A core switch ties switches together.


Where is the driver side headlight fuse located in a 2002 Volkswagen Jetta?

They should be both tied in together


Which company manufactures the Golf car?

The Golf car is manufactured by the German automobile company Volkswagen. The Volkswagen Golf is in the list of best-selling cars of all time generated by the website 24/7 Wall St. together with two other Volkswagen manufactured cars.


Can you be married in Catholic church if you already have a child together?

You can, but you should go to Confession for engaging in premarital sex (which is a mortal sin).


Did all of the member of Three Days Grace start together?

no there has been some switches in band member but Adam was from the original start.


What are the three common types of media used to connect two switches together?

copper, radio (microwave), or fiber optic cable


What do you typically find in a ganged switch box?

Usually switches brought together in a central spot for convenience. There could be one or more supply feeder and load connections to each device connected to the bottom side of the switches. In the back of the box there will be all of the cable ground connected together and placed under the ground set screw.