0
Yes. 230V line to line is considered single phase power. The 115v half part of that is called split phase. It should not be called two phase, as it is one phase that has been center tapped and grounded at the neutral point - it is still one phase power.
Answer230 V is the standard nominal voltage for residences in Europe. 230 V is the line-to-neutral voltage (phase voltage). Low-voltage distribution is by three-phase, four-wire, system with a nominal line voltage of 400 V and a nominal phase voltage of 230 V.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
You have 230v 3 phase power can you plug a 230v single phase motor into it?
Any two legs of a three phase system are classed as single phase. So yes a single phase motor will operate when connected. Be sure to use the proper motor protection devices to control the motor.
How do you convert 3phase connection to 2 phase?
Any two legs of a three phase system can be classed as a single phase supply.Alternative AnswerAs the above answer points out, connecting a load between any two line conductors of a three-phase supply will give you a single-phase load. But you must, of course, take into account the voltage rating of the load you wish to connect.In Europe, three-phase low-voltage distribution is normally by means of a four-wire system, comprising three line conductors and a neutral conductor, operating at 400 V (line-to-line) and 230 V (line-to-neutral).Your single-phase load's voltage rating must, of course, match either the single-phase supply's line-to-line or line-to-neutral voltages. In Europe, most single-phase loads are rated at 230 V so, for a residential three-phase, four-wire system, it is usual to obtain a single-phase supply by connecting the load between any one of the line conductors and the neutral conductor.But, if you have a non-standard, 400-V single-phase load, then connecting that load between any two line conductors will also give you a single-phase supply.
Is line to line fault a 3 phase fault?
'Line conductors' are the three 'hot' conductors (A-B-C) that connect a three-phase supply to a three-phase load. In some cases, a pair of line conductors (e.g. A-B, B-C, or C-A) is used to supply a single-phase load. A 'line fault' can be a short-circuit fault between all three, or any two, of these line conductors -whether they supply a three-phase load or a single-phase load.
How you can convert 1-phase voltage to 3-phase voltage and vice-vars a?
A single-phase supply is obtained between any two line conductors or between a line and neutral conductor of a three-phase supply. To obtain a three-phase supply from a single-phase source is far more difficult, and requires additional equipment.
How do you convert 230v to 208 volts single phase?
A source of 208 volts can be obtained from any two legs of a three phase four wire 208 volt system. The two legs are classed as single phase 208 volts. The lead tags can be L1-L2, L2-L3, or L3-L1 all of which will give you 208 volts. Any of these lead tags to the grounded star point (wye) will give you 120 volts.
Can you convert 415v 3 phase to 230v single phase?
415V 3 phase is the line to line voltage. The line to neutral of this supply is 230V single phase. Therefore you use one of the phases and the neutral.
What is the Single phase voltage in India?
The single phase voltage in India is 230v when we check with the phase and the nutral single line
What voltage you get at home in India?
The single phase voltage in India is 230v when we check with the phase and the nutral single line
What is 3 phase voltage in Germany?
Three-phase voltage in Germany is 400V, single-phase voltage is 230V.
What is the amperage of a 20 HP 240v single phase motor?
Typically single phase motors go up to 10hp. Wouldn't be very efficient at about 100 amps. A 20hp 3 phase motor at 230v pulls 52 amps. The 10hp single phase 230v pulls 50 amps.
You have 230v 3 phase power can you plug a 230v single phase motor into it?
Any two legs of a three phase system are classed as single phase. So yes a single phase motor will operate when connected. Be sure to use the proper motor protection devices to control the motor.
The motor states 120v single phase to operate.can you use it using 230v supply in Singapore?
Absolutely not. In the U.S. all power is 120v on a single line (one hot, one neutral, one ground) overseas all power is 230v on a single line. Will fry your unit. You can however by a step down or up transformer fairly cheaply at radio shack.
Are all 230v circuits three phase?
No. Most home services in the US and Canada are 230V single (split) phase.Answer (for European Systems)230 V is the standard nominal single-phase voltage for European low-voltage distribution systems.In urban (and built-up rural) areas, low-voltage distribution is practically always a three-phase, four-wire, system by means of underground cable or overhead line. This provides a 400 V line voltage (line-to-line) and a 230 V phase voltage (line-to-neutral).In rural areas, individual buildings such as farm houses, may be supplied with single phase directly from a distribution transformer (e.g. in the UK, using a pole-mounted 11-kV/230-V single-phase transformer).In most cases, residential buildings are provided with single-phase supplies but, in some countries, residential buildings are provided with three-phase supplies.
HOW and Why there is 440v supply in three phase and 230v supply in single phase?
because all over the world there is an standard rate of voltage
Three phase voltage in india?
It is 230V single phase and 440V in 3 phase system at 50 Hz.AnswerIf the single-phase voltage is 230 V, then the three-phase voltage must be 400 V, not 440 V. The line voltage is 1.732 times the phase voltage.
Why is residential wiring called single phase if there are 2 phases coming in?
residential wiring are called single phase because the 2 phases coming in are one is neutral and the other is line.the neutral has a potential zero with ground and it is to provide a closed path for the current to flow through..the line is having a potential of 230V with the ground and a line together with a neutral is called a phase
How many wires are there in 120 volt single phase power and how are they marked?
Verify wiring layouts by making measurements, before connecting and/or energizing equipment. A 120V single phase 2 wire should have one hot wire, a 230V single phase 2 wire should be assumed to have two hot wires, and a 230V single phase 3 wire also should have two hot wires.
