0
Keep in mind that the supercharger is driven off of the pulley clutch.
Check the specs for the sizing of the N/A vs. S/C.
Many companies offer an oversized pulley for a S/C if you want to change your boost range and shift it a little higher in the RPMS.
I've had luck with the NST pulleys and it comes with a new kit for all of your pulleys.
Check it out if you don't mind going with non-oem parts.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What motors can you put in a 1991 toyta tercel?
3e-e, 5efe, 5efhe, 4efte, 3ete, will all bolt up and be the cheapest. a 4age, 4agze, or 3sgte will fit with some frame modifications. basically you can put in any motor that will fit in the engine bay if you got enough cash.
Is it possible to use a 4age head redtopbluetopsilvertop on a 4af block?
well look at there names...4afe and 4age.....key is 4a....meaning they have the same block just different heads.....so yes it will fit.
Why would the pulley to the block of a car not be moving?
clear as mudpullies are normally attached to an engines crank either by being directly bolted to the nose of the crank which has a taper machined into it and is retained by the pressure exerted by the attaching bolt which screws into the nose of the crank. The other method is to fit the pulley over the crank nose which has a valley or keyway machined along about an inch or so along the length of the nose and then place the pully onto the crank nose and line up a corresponding machined keyway in the pully and insert a metal key into the space created by the keyways. pullies will remain stationary if a key fails or is sheared,or if the pully bolt has fallen out and the pully has become loose on a tapered crank or the other cause is when the rubber dampener which circles the mid section of the pulley perishes thru from contamination by fuel and oil etc the crank continues to rotate with affecting the pulley. so there,it is ,clear as mud. razmo ANS 2 -If this pulley is not moving, the crankshaft is not turning.
Will a 1991 mr2 turbo transmission fit mr2 1987 motor?
The 3SGTE motor is completely different from the 4AGE or 3A motor, simple answer is no.
How do you remove a crankshaft pulley bolt from 1997 Isuzu rodeo?
Take out number one spark plug (or all to make it easier to turn) fit a socket to crank pulley bolt and turn the crank until it's just after TDC say thirty degrees. Feed about 900mm of 10mm rope into number one cylinder but don't drop it all the way in. Turn the crank back until you get a firm resistance and apply a breaker bar to the socket. Apply pressure to the breaker bar until the bolt undoes. You will probably need to remove the radiator and fan assembly to be able to get to the crank pulley unless you have already done so.
How do you get to TDC on an 89 240sx?
Pull the front plug and turn the engine until it breathes on you w/ pressure through the plug hole. then put a dial guage rod into the plug hole and when it reaches top, that is TDC Edit: A dial gage rod is not needed, anything that will fit into the spark plug hole will do. You can be sure your on TDC by looking at the crank pulley there are lines on the pulley and a pin sticking out from the front of the engine make sure the second mark from the right on the crank pulley line up with the pin
Where to find a puller to remove crank pulley in order to change water pump on a 1996 Dodge Intrepid?
Check with your local auto repair shot to see if they rent tools. If so, they likely carry a crankshaft pulley remover. I'm in the process of changing the water pump on my 2002 Intrepid and I rented the tool. Now I have to find the installer because the one they had didn't fit my pulley.
Will a 4age engine fit into a daihatsu charmant?
Yes. Very easily if it is running 4A-C engine. More adjustment if it has K series. Head on to charmant4age.blogspot.com for more info.
'timing marks' on a Mazda b6 engine?
The timing marks on the crank pulley are 2 little nicks about half the size of a pinhead about 1cm apart. The 'clockwise' one is the ignition timing mark. The one to it's left is TDC. To correctly fit timing belt, crank pulley should be at TDC on the compression stroke & 'E' & 'I' on the cam sprockets should be at 12 o'clock. It's that easy. But the camshafts can move on their own because of the valve spring pressure on the cam lobes, so make sure the camshafts don't move while your trying to fit the belt.
Is there a special tool for harmonic balancer on 2008 ford 4.6 liter?
You need a puller. Most engine supply places have them. They thread into hole at end of crank & pull of balancer by gripping the three pulley holes & pushing against crank. You just need one with threads that fit your crank but most are multi-smaller to large, & insert until they catch. They're around 20-25.00 (US)
How do you fit a fanbelt to a Ford Fiesta mark 6 2003?
The quickest way is to take a picture of the belt routing then cut the old belt off the new belt is a stretchy design you use the special tool you get with a genuine belt from fords and lace this over the water pump pulley bolts then stretch the belt on by rotation the crank pulley
What is lacrosse heads fit on the stx crank shaft 7075?
there are some gait ones that fit
