0
Can't start 1989 Chevy Suburban with the key only by directly wiring starter is there a fuse link from the ignition wiring to the starter?
Wiki User
∙ 19y ago
Generally the problem is either a defective neutral safety switch or a bad ignition switch (not ignition key lock).
Wiki User
∙ 19y ago
Add your answer:
Earn +20 pts
1993 Chevrolet pickup starter wont engage when you turn the ignition on. the battery is good and i put a new starter on?
check your wiring, if all your wiring is good then test your ignition relay, if its not the starter, not the battery, and not the wiring there's only one thing left. Good Luck with the repair
Why makes the starter on 1998 silverado engage when the positive cable is connected and the key is not in the ignition?
Did you put a starter on it ? If so, Then you have put the starter wires in the wrong place are you have the big battery wire touching the small wire that goes to the starter. Recheck the wiring on the starter.
You replaced your starter in your 1993 grand am and your car wont start not ever a click from the starter why?
We had the same problem in our '97. Check that your battery is fully charged and working properly, also check that the alt is working. If both of these are in working order it could be a faulty ground wire or the starter wire. Then, if those check out fine, I would start checking into your ignition switch and modular. I traced our issue backwards. If you know that the starter and the alt is good then it has to be in the electrical part of the car. Wiring or ignition. Hope this helps. If by chance it's something else please let me know. We finally found our problem in the ignition wiring. We had a bad wire going into the module. We have to push up on the wiring to get the starter to jump. Still a reliable car.
Fuse keeps blowing for ignition need wiring schmatic for ignition and starter for 1997 dodge stratus 24 engine or for an answer as to why you have this problem?
You will need to replace your starter, this happened with my car a couple days ago, I brought it into the shop, got the starter replaced and the fuse does not blow anymore. It happens because the starter draws to many Amps of electricity due to age, amount of use etc.
How do you wire ignition in lancer?
what about the ignition switch wiring
Where can I find a picture of 1974 Volkswagen beattle starter wiring?
very very simple wiring---it goes from the ignition switch to the fuse box--then directly to the voltage regulater and then straight to the starter solenoid
How do i change the ignition module in a 1998 suburban?
Begin by removing the wiring harness from your 1998 Chevrolet Suburban ignition module. Remove the ignition module retaining screws. Reverse the process to install your new ignition module.
1993 Chevrolet pickup starter wont engage when you turn the ignition on. the battery is good and i put a new starter on?
check your wiring, if all your wiring is good then test your ignition relay, if its not the starter, not the battery, and not the wiring there's only one thing left. Good Luck with the repair
What causes a 87 Nissan truck not to turn over?
check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay. check for power to starter; check fusable links at positive battery connection, can you jump starter directly with power source? if not maybe the starter should be taken out and inspected/bench tested. given the year I suspect wiring/connection issues. a worn out ignition switch would be common for this age of vehicle. check operation of starter relay.
Why do your Jeep Wrangler starter engage when you turn on the ignition?
It sounds like your ignition switch has gone bad. If you have done some sort of work on the starter recently recheck your wiring.
How do you change a starter on a 1996 suburban?
Disconnect the battery. The starter should have two or three bolts holding it in. And there will be wires connected on it. Loosen the bolts and wiring connectors, then remove the starter from its mount.
Battery works starter will not turn Is it the starter?
That is not anywhere near enough information to make a determination about the status of the starter. Could be the starter, but could be the starter solenoid, wiring problems or even the ignition switch.
Why would my truck not start with aNew starter battery alternator?
check the wiring change the starter relay and clean ignition switch with electicial cleaner.
Where is a solenoid on a 312 v-8?
the solenoid is located below the starter. if your looking to bypass the wiring to the ignition, dont do it often or you will burn the brushes in the starter
Why makes the starter on 1998 silverado engage when the positive cable is connected and the key is not in the ignition?
Did you put a starter on it ? If so, Then you have put the starter wires in the wrong place are you have the big battery wire touching the small wire that goes to the starter. Recheck the wiring on the starter.
How do you change the starter relay on a 1999 ford windstar?
The relay is located in the 12 volt ignition wiring harness going to the starter. The small wire on the starter is the ignition switch. The relay is located in the wiring harness. Are you sure the starter solnoide is not bad? When the ignition key is turned to the start location, you should read 14.1 volts going to the starter. If you read 14.1 volts, and the starter does not turn over. Check battery, and cables. Ok, Then replacement of starter is necessary. Starter bolts are 13mm. Brakeline bracket bolt is 15mm. Solnoide bolts are 13mm. Should take no more than 20 minutes to remove starter.Follow the + battery cable either mounted on the inner fender or on top of the starter
You replaced your starter in your 1993 grand am and your car wont start not ever a click from the starter why?
We had the same problem in our '97. Check that your battery is fully charged and working properly, also check that the alt is working. If both of these are in working order it could be a faulty ground wire or the starter wire. Then, if those check out fine, I would start checking into your ignition switch and modular. I traced our issue backwards. If you know that the starter and the alt is good then it has to be in the electrical part of the car. Wiring or ignition. Hope this helps. If by chance it's something else please let me know. We finally found our problem in the ignition wiring. We had a bad wire going into the module. We have to push up on the wiring to get the starter to jump. Still a reliable car.
