0
No, it is more likely to shift if the tire is rotated in the opposite direction.
No, damage from a hard impact or a puncture will cause a slipped belt.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What causes a steel belt in a tire to shift?
Faulty construction of the tire of damage from a road hazard.
Can you feel a tire with your hand if a steel belt has shifted?
YES - A broken tread or side belt will cause a shimmy or shake while driving. Also another way of telling if you have a belt shift is look directly at the tread face. If its broke the tread will actually be S shaped... hence the term S Shaped Tread. If you notice a belt shift replace the tire. I was a tire installer for 8 years and seen some horrific accidents caused by belt shifts in tires.
What year 350 sbc has reverse rotation water pump for surpitine belt?
All serpentine belt driven water pumps on SBC engines are reverse rotation.
Do the kuiper belt rotate on the axis?
The Kuiper belt is not an object; it is a region of the solar system. Therefore it does not have an axis of rotation
How often do you need to change a previa cam belt?
The belt that you refer to is a self adjusting steel belt that is inside the engine. It does not need replacement.
Does lift rhymes with belt?
No, the word lift does not rhyme with the word belt. Lift does rhyme with sift, shift and rift though.
Would slow puncture cause steering wheel wobble?
you could have a broken steel belt in one of your tires, that happened to me. I had a tear in my right tire that caused that in my 91 Roadmaster.
Is the distributor rotation on a Chevy 350 clockwise or counter clockwise?
Not true, if you look at a 1989 Distributor rotation for example on a LO5 350 TBI. you will see the distributor rotation is counter clockwise. Looking at the cap where it is square #1 is on the right then #8 next to it on left of square then so on in a counter clockwise rotation. #1 and #8 are positioned toward firewall. Believe this started in 1988. Now on my 1987 LO5 350 it's a clockwise rotation distributor with #1 up front toward front of car with #8 to the right of it and so on in a clockwise rotation. There also seems to be a lot of confusion on rotations of water pumps. My 1987 GMC Jimmy ( full size) LO5 350 was equipped from the factory with a combination serpentine/v belt System with one of the v belts running the water pump. Because the v belt runs the water pump it is a clockwise rotation pump. On 5.7 350 with full serpentine systems they are reverse rotation. If the pulley is of the v design it's a clockwise rotation pump if it's smooth it's a reverse rotation. Belt goes around the circumference of belt like the v belt does it's a clockwise rotation. If the back portion of the belt( serpentine ) contacts against smooth pulley it's reverse rotation.
Can the fan belt cause a squeaking sound?
would the fan belt on a v8 motor cause squeaking
Your belt on your 1996 Honda Civic Dx makes noises when you down shift or stop what belt is that?
It can be the cam belt or the serpentine belt. The cam belt must be replaced every 90,000 miles. Warning: This is an interference engine. If the belt breaks you will have serious engine damage. Replace the cam belt if it is due for replacement. Inspect the serpentine belt and replace if you see any cracks or fraying. If the serpentine belt looks fine or you replace it and the noise is still there, replace the cam belt no matter when it was last replaced. It can be the idler pulley for the cam belt needs replacing and is not holding the correct tension on the belt. This can cause the belt to break even if it is new.
What materials are used to manufacter a belt sander?
Steel, plastic and rubber.
What is the difference between a belt and a motor-driven platter rotation?
The difference is the belt starts to slip very minute differences in tonation, direct drive is better.
