0
My first guess would be that you haven't disconnected the flywheel bolts from the torque convertor. To do that you need to locate the access hole and rotate the engine crankshaft until a bolt appears in the hole. Remove it and continue to remove bolts until you have them all. Usually about five bolts but some use 4 and some use more. I you have already removed the flywheel bolts, you need to keep looking for something holding you up. Sometimes you need to pry it a bit to get it broken free.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can the flywheel be removed and replaced without removing engine or transmission i'n 1978 Chevy 350 motor?
NO. You will have to remove all the transmission bolts and slide the transmission back enough to get a wrench and your hand between the engine and transmission to remove the fly-wheel bolts.
Can you replace Chevy flexplate without removing tranny?
You will have to slide / move the transmission back enough to get your hand up in between the flywheel and toqure converter so you can remove the flywheel bolts. You do not have to compleatly remove the transmission. I do it all the time.
How do you remove a 1998 Nissan Sentra transmission?
To remove a 1998 Nissan Sentra Transmission, you first need to locate all of the bolts. From there, you will remove the bolts. Undo any wiring or tubing that goes into the transmission. From there, it can be taken out.
What is the Trick for getting to and removing all the bolts on 93 ranger manual trans?
1. wheels-chalked for safety e-brake on. remove drive-shaft support tail shaft of transmission with hydraulic jack remove cross member supporting transmission lower back of transmission just enough to reach upper top bolts with long extension and socket NO trick just experience .
How do you remove a 4.3 vortec engine from a 97 Chevy Cheyenne 4x4 without removing the transmission?
REmove and mark with masking tape all hoses and wires and linkage that connects to the engine. Mark where it came from on the engine with an identical marking for ease of reinstallation. You will need to remove the bolts that hols the transmission to the engine and under the flexplate cover remove the bolts that hold the torque converter or clutch to the flexplate. Remove the engine mount bolts. The engine should be ready for removel, but be sure the tranny is supported somehow so it does not fall.
What is the procedure for removing the a 5-speed manual transmission on a 1998 Dodge Ram 1500 4WD with a 5.2L engine?
To start, remove the drive shaft from the rear end.( there should be four bolts holding it on). Remove the shifter completely. Next, remove all of the bolts from the bell housing that fasten the tranny to the rear of the engine.(you will need to remove the starter and oil filter to complete this). Then, place a jackstand underneath the transmission and remove the crossmember with the transmission mount. In most cases, the collector pipe for the exhaust will need to be unbolted from the headers. Before removing the tranny, make sure all wires and clutch connections are removed. At this point, you should be able to drop your transmission. - good luck, and be prepared to spend a few hours doing this.
How do you replace the radiator on a 1998 Malibu?
on the bottom of the radiator there is a plastic mount with two bolts on each side, removing them can be difficult if they are at all corroded. try not to break them when removing them, otherwise you will have to re-drill the holes and replace them with some bolts and nuts which is very time consuming. other than that just remove all hoses and transmission lines attached to the radiator and it should come right out.
How do you remove a oil pan gasket in a 1974 Nova?
Remove the oil pan by removing all the bolts. Then you will probably have to scrap the old gasket off.
How do you replace the manual transmission clutch on a Chevy s-10?
If this is a 5 spd S-10 2000, .... Then disconnect the hydraulic clutch cable from the transmission. Remove the bolts that hold the bed to the frame. Jack up the bed of the truck to give yourself about 6-8 inches. This will allow you to reach the bolts to the bell housing. Make sure you remove the gear shifter, boot cover too. Drop the drive line, remove the exaust pipes from the manifold and get them out of your way. place a transmission jack under the transmission and begin removing the bell housing bolts. Once the bolts are removedbring the transmission down and back. when you can see the hydraulic clutch, simply remove it and replace. Ensure you bleed off all air from the clutch once you re-install the transmission. (Raising the bed of the truck is the only way you will get to the bell housing bolts and allow yourself room to bring the transmission back and down).
How do you remove the headlight assembly on a 2008 Toyota Avalon with D4R HID self leveling headlights?
In order to remove the headlight you must remove the whole bumper, that means removing the plastic grill cover, then removing all plastic under the bumper, removing the inner wheel arch, then removing 2 bolts on the bumper, one per side, then pull out, there will be 4 tabs per side, then remove 3 bolts holding the headlight in
How do you put a transmission in a Mazda 929?
i've done this on my 88 929 it's pretty straight forward. 1. remove flywheel belhousing cover on the bottom of the transmission in the front. i think there are four bolts. 2. you must then remove flywheel bolts from torqu converter there are 4 bolts. use wrench on front balancer pully bolt to turn engine to acces all bolts. 3. support the transmission with jackstands on the front and rear of transmission. remove transmission fluid line there are two. and then disconnect electrical wire harness. 4. check clearance, i dont remember but you might have to remove dipstick and tube. 5. remove bellhousing bolts from transmission thereare about six the connect transmission to the engine. 6. remove transmission mount bracket. 7. disconnect shift cable from floor shifter to the trans. 8.jack up transmission with floor jack and remove mounts ,lower transmission out of car.
How do you remove the engine from an Isuzu Rodeo when all bolts have been removed and the engine is loose?
its a vague question but i think you need to separate the transmission from the engine they are connected with a splined shaft and they must be pulled straight apart before removing
