answersLogoWhite

0


Best Answer

Yes it definitely can as at least 12 volts is required for everything with the exception of the computors and sensors. They require 5 volts.

I'll add this tidbit. If the battery drops below 8 volts the starter motor will still turn the engine but the ignition will not fire and the engine will not start. This can happen if one or two cells in the battery fail, and of course if an electrical load is connected over night (i.e., head lamps, internal lamps, trunk lamp, CD player, etc). Battery voltage must be tested under load as follows: attach a voltmeter to the battery terminals and have someone try to start the car. The starter becomes the load and the voltage may drop a volt or two if the battery is good and properly charged. FYI

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Can the battery going dead on a 2001 Chevrolet Malibu make your ignition not work?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

I can't remove the key from my 1999 Malibu ignition switch How can this be fixed?

you are going to have to take the whole key cylinder out.


What could cause the engine light to blink on a 1997 Chevrolet Malibu LS?

Most likely a ignition or fuel problem. Blinking is a major warning something is wrong, try going to a auto zone as they can check codes to let you know the problem. Hope this is a little help


I have to turn the ignition key several times before it will start. I doesnt do it every time. The battery is ok. Any ideas?

Ignition switch going bad, corroded or loose battery cables, starter relay or starter going bad.


I have a 2000 s10 and i have no power going to the starter.?

check your positive on your battery. verify if no power is coming from the battery OR from the ignition. hard to answer without knowing if the problem is coming from battery or ignition. look for burnt wires going to the solenoid. hope you get a more precise answer. good luck. it could be worse!


How much transmission fluid does it take to fill the transmission on a 1998 Chevrolet Malibu?

For a complete change it's going to take 10 qts.


Why will car ignition not turn over on the first attempt but will on the second?

I would suspect you have an ignition switch going bad, a starter solenoid that may be going bad or more than likely corroded or loose battery cable connections. Check the battery post connections first.


How do you change the fuel pump on a 2002 Chevrolet Malibu?

The best thing you can do if you are going to do this rather than have a repair shop is to purchase a Haynes Manual that is specific to your car.


What causes the ignition light on your 1990 Fiesta to come on when the engine is switched off even with keys removed from ignition?

check for a bad earth strap going t gearbox to battery


What can i do - alarm keeps going off when i turn ignition key?

If your alarm goes off while you turn your ignition key this could be signaling a problem with the vehicle's power. Have your battery tested to ensure that it has enough juice to power your vehicle. You may then want to look for corrosion on the battery posts or battery cable ends.


When you turn the ignition the volts going to the starter are less than 7 volts Why?

whats the battery voltage start there and test your way down


Why is battery going dead in your lawn tractor?

Either the battery has a dead cell, which will require you to replace it, or something is on pulling power from the battery. Disconnect the negative cable and leave it off overnight. If the battery is dead the next morning the battery is defective. If not, then find out what is pulling power from the battery. Ignition switch may be defective.


How can i changi the ignition lock cylinder in my 2000 Chevy Malibu?

You need to take the dash apart to get to it. I had the same problem in my 2000 malibu. Are u having a theft system problem? I was. You need to take the ignition apart too. Your going to need to reprogram the new ignition lock cylinder with your computer. To reprogram just turn the key to the on position (dont start it) let it sit for 10 minutes, repeat this 3 times. It should be programmed now. Now start it.