0
This question really doesn't belong in a Health category. The question is an occupational health question. Cutting metal with a laser, in this case galvanized steel, is much like arc welding or flame cutting on metal. In most if not all states, this is legal as long as the fumes emitted from the operation doesn't exceed OSHA's Permissible Exposure Limits for metal fumes, especially zinc in this case. Some states may have lower limits than OSHA for these metal fumes. Ventilation must always be used, and metal fume sampling should have been conducted to verify exposure levels. Every state has at least one OSHA office and one State run OSHA Consultation Office you can call with questions. In many cases, the employer can contact the State Consultation Office and they will conduct the sampling for free if the employer agrees to correct any hazards identified during the visit This website www.osha.gov will allow you find the contact information for each state and contains information on metal fumes, welding, cutting..etc. Hope that helps.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How much damage does a 100kW laser do Would it be powerfull enough to stop a tank or shoot down a jet What would happen if it was shot at a solid rock surface or a person?
I know a 4KW gas laser can cut 1 1/4" into average grade steel. Assuming you're refering to this type of laser then 100kw gas laser should be able to cut into about 2 feet of steel. Yikes. Imagine if it were a 100kw chemical laser!!
What is galvanized iron used for?
Galvanization is a treatment used in the manufacturing of iron and steel to prevent rusting. It involves applying a zinc coating.
Can a laser cutter cut diamond?
yes
Where is galvanized iron used?
HI, There are a wide range of uses for galvanized iron, which comes in pipes, stakes, sheeting, and wire, among other formats. Many hardware and home supplies carry galvanized iron products and may be willing to cut pieces to custom sizes by request. People can also be referred to professionals who will weld or cut galvanized iron to meet the needs of a particular project. For people who use galvanized iron, it is a good idea to periodically inspect the iron for any signs of corrosion so that they can be addressed early, before they have a chance to spread.
Can you laser cut brass?
yes, like most metals...
Can galvanized metal be laser cut?
Yes im laser cutting some right now. But the fumes are probaby toxic.
How much damage does a 100kW laser do Would it be powerfull enough to stop a tank or shoot down a jet What would happen if it was shot at a solid rock surface or a person?
I know a 4KW gas laser can cut 1 1/4" into average grade steel. Assuming you're refering to this type of laser then 100kw gas laser should be able to cut into about 2 feet of steel. Yikes. Imagine if it were a 100kw chemical laser!!
What is galvanized iron used for?
Galvanization is a treatment used in the manufacturing of iron and steel to prevent rusting. It involves applying a zinc coating.
What is steel cutting?
It depends on how thick of steel you're aiming to cut. But most job shops process steel with either laser cutting (for thin steel) or waterjet cutting (for up to 12" thick)... or machining.
What kind of laser will cut matal?
A burning laser will cut the metal
What would happen if a laser burned your retina?
If a LASER device burned you retina, you would mostly or completely blind in that eye. There would most likely be no way to repair the damage. Keep in mind that LASER beams can cut through steel !
Is Laser cutting of steel a thermal cutting process?
CO2 laser cutting carbon steel with oxygen is an exothermic (thermal) process. The oxygen used with the laser cutting burns the steel, thus assisting the cutting process. This process causes striations, or lines, to form at the cutting edge and provides lower cut quality but faster cutting. In contrast, when cutting stainless steel with nitrogen, only the heat from a CO2 laser performs the melting (operating in the far infrared region at 10600 nanometers). The nitrogen assist gas pushes the melted material down and out of the way, leaving the cut that is typically a polished edge.
How can you cut steel?
It depends on how thick of steel you're aiming to cut. But most job shops process steel with either laser cutting (for thin steel) or waterjet cutting (for up to 12" thick)... or machining. I'd look for any of those services in your area and see what comes up. ThomasNet.com is a good resource for doing so.
How to What Types of Materials Can Be Cut Using the Laser Cutting Services Offered by Central Laser Services at Central Profiles?
Central Laser Services, a division of Central Profiles, offers laser cutting services for a wide range of materials. They use state-of-the-art laser cutting equipment to cut materials with precision and accuracy. Some of the materials that can be cut using Central Laser Services include: Mild Steel: Laser cutting is an efficient way of cutting mild steel up to a thickness of 25mm. Stainless Steel: Laser cutting can be used for both thin and thick stainless steel sheets, making it ideal for a wide range of applications. Aluminium: Laser cutting is an excellent option for cutting aluminium sheets up to a thickness of 12mm, producing clean and precise cuts. Brass: Laser cutting produces high-quality cuts on brass sheets of up to 6mm in thickness. Copper: Laser cutting can be used to produce intricate designs on copper sheets up to 6mm in thickness. Acrylic: Laser cutting is ideal for acrylic sheets of up to 25mm in thickness, producing smooth and polished edges. Central Laser Services can also cut other materials such as plastics, woods, and composites. They can provide custom laser cutting solutions for customers with specific requirements.
What is the Methods of laser cutting?
There are many ways to cut with a laser. In many cases, a highly concentrated spray of gas or water is sprayed right behind the laser to blow out the recently cut steel, leaving a nice, clean cut. Another method used involves heating the material to its boiling point and vaporizing it; however, this can only be done with materials that do not melt, such as wood. A final method involves cracking very brittle materials with the heat of the laser beam then directing that crack with the heat of the laser beam to make cuts.
What materials can be cut with a laser cutting machine?
Laser cutting machines cut through a large variety of materials, but there are several laser technologies. CO2 laser can cut organic materials like wood, paper, cardboard, fabric, acrylics and plastics.
Can laser cut aluminum?
well it depends on what kind of laser your talking about......
