0
What else can I help you with?
What ohm should the speaker be if i want to achieve a 2 ohm load from 4 speakers?
Four 8 ohm speakers wired in parallel would give an effective 2 ohm load.
How do you wire two 8 ohm speakers and keep a 8 ohm load?
in parallel No. Two 8 ohm 'speakers in parallel present a 4 ohm load.
If two four ohm single voice coil subs are wired in parallel how many ohms will be on the amp?
Two four ohm speakers in parallel is two ohms. Make sure the amp is rated for that load impedance, or you could damage it.
Can resistance be added to speakers to make a 4 ohm speaker have an 8 ohm load?
You "can" add a four ohm resistor in series with a four ohm speaker, and make it look like an eight ohm speaker, however, the frequency response will not be the same. It is better to use to correct speaker for the amplifier, or use two four ohm speakers in parallel. That resistors power rating must exceed the rating of the speaker. Half the from the amplifier will go to the speaker, while half will go to the resistor, making it get quite hot.
How do you wire two 4 ohm speakers into 2 a two ohm load?
Parallel
What ohms am i running if i have two 4 ohm speakers hooked up to my amp vs two 2 ohm speakers?
Don't know how you have subs wired but should be 4 ohm load is what your amp will see.
How do you use 16 ohm monitor speakers with an 8 ohm powered mixer?
Just use it like an 8 ohm speaker or else connect two 16 ohm speakers in parallel to form an 8 ohm load. Parallel is positive to positive and negative to negative.
What would make a 1992 oldsmobile's radio smoke?
the factory radio is bad on the inside or speaker ohm load is different are your speakers aftermarket?
What ohm load will 4 12 in dual 2 ohm play at?
There are a lot of possibilities here, especially since your question is worded exactly right.I'm taking it you have 4 12" speakers, each of which have Dual Voice Coils (2 Ohms each). You want to wire them together and see what ohm load you have.Ok, there's multiple ways to wire this up. Series, Parallel, and Series/Parallel combo.Wiring these speakers in series can give you either a 4 ohm load, or a 16 ohm load. 4 ohms if each speaker by itself (having DVC) is wired in parallel and 16 ohms if each speaker by itself is wired in series.Wiring these speakers in parallel can give you either a .25 ohm load, or a 1 ohm load. Again .25 ohms if each speaker by itself (having DVC) is wired in parallel and 1 ohms if each speaker by itself is wired in series.Wiring these in a series/parallel configuration can give you tons of different wiring options and ohm loads. In your case .75, 1, 3.2, 4 ohm loads.So your best option would to be wire your speakers up in series, with each speaker wired in parallel to itself. This way you'll get a 4 ohm load, if done properly. Make sure your amp can run a 4 ohm load too.
What load would 2 sets of 4 ohm speakers equal?
4ohms in series,2ohms in parallel.
How do you wire multiple speakers together?
Speakers can be wired in parallel or in series. Take the speaker wire from the output, and wire the speakers like so: (ignore the squiggles, they represent spaces) ----|------| S S ----|------| For a parallel wiring. This will reduce the impedance of each speaker, though, so two ohm speakers should be used insead of four ohm speakers. Wire them like this: ----| S | S ----| for series wiring. This will increase impedance though, so eight ohm speakers should be bought instead of four. You will be fine using four ohm speakers in either case, but will lose clarity.
Can a 4 ohm receiver drive 3 ohm speakers?
If you connect four four-ohm speakers in parallel, the impedance will be equal to 1 ohm, and will allow the speakers to run at the advertised watt RMS. The equation is 1/(total impedance) = 1/(impedance 1) + 1/(impedance 2) and so on. Parallel is like this: Power source: + Speaker+: + + + + Speaker-: - - - - Power source: - However, usually if you hook up a 4 ohm speaker to a 1 ohm amplifier, it would still function it would simply not provide nearly as much wattage as it would have otherwise. Also, if your speakers are dual voice coil (like many subwoofers) you could use 2 4 ohm speakers, connecting the two voice coils on each speaker in parallel and then connecting the speakers themselves in parallel.
