If you have any repair skills at all you should be able to do it. Anything up to 6-8 inches, you can patch with a piece of drywall and some mud. Bigger than that, you should have something behind the drywall to screw to.
Small hole. Clean up the hole by cutting it back to solid drywall. Doesn't have to be square or perfect. Take a piece of drywall 2 inches bigger than the hole and on the back side, score the paper 1 inch in all the way around. Just through the paper. Snap the drywall and peal it off of the front paper, leaving the front paper intact. Butter the flap of paper all the way around. Place the patch in the hole and work out the mud with a wide putty knife. Much the same way as smoothing wall paper. Top coat the entire patch with joint compound (mud), let it dry and lightly sand. Two coats will probably be needed. If you are inexperienced with sanding, you can "sand" the mud with a damp sponge. Rinsing often.
Big hole. Either cut back to the center of the studs on either side, or cut out the hole and use 2-3 inch wide strips of plywood behind the drywall to screw to. Screw the plywood to the existing wall first and then set the patch in place and screw it. Use joint tape on the joint and finish with mud. You will need to feather out the mud 6-8 inches past the joint.
A similar approach (with images showing how it's done):
Patching the hole is easy. Making the repair invisible takes some artistry, but it's actually fun to see how well you can match the surrounding finish. The best method actually starts with enlarging the hole! You saw out a nice rectangular opening around the damaged area, then cut a new piece of drywall to match the dimensions of the opening. Here's a link to some illustrated step-by-step instructions that show the details:
http://www.diyadvice.com/diy/drywall/repairs/holes/
Either cut out a square to the center of each joist either side of the hole and replace the drywall with a new piece cut to size. then tape and mud the joints. Also there are metallic screen patches made for small holes that stick to the existing drywall, and can be mudded over to fix the hole.
I tape the broken vapour barrier with red 'Tuck' tape then put a wood backing in the hole and use small pieces of drywall to patch.
You can repair it with a welder or you can replace it.
There are a few ways that you can repair a large drywall section. One way is to use a patching compound and apply it over the area that needs to be repaired. Another way is to use a drywall adhesive to attach a piece of drywall over the area that needs to be repaired. Cut a piece of drywall to fit the hole. Attach the drywall to the studs with drywall screws. Cover the seams with drywall tape. Cover the entire patch with joint compound. Let the joint compound dry. Sand the joint compound. Paint the patch. For getting the professional drywall patch repair service contact us.
"Have a hole in your socks" means you wore them out. It also means you should either repair them or replace them.
It depends on the size of the hole.For the smallest holes (less than an inch or so), you need spackling paste and a putty knife. Fill the hole with spackle, wipe it level with the wall with the putty knife, and let dry. Paint.For medium holes (about 1" to 8" wide), you will need an aluminum patch, which is sort of like a mesh grid, patching plaster, a sanding sponge, and a large putty knife. Put the mesh grid up to the hole, and use the plaster to coat the grid and blend it into the surface of the drywall. After it has dried, sand it even. Prime and paint.For larger holes (larger than 8"), you will need a drywall patch, joint compound, a sanding sponge, drywall screws, a screwdriver, and a compound knife (to spread the joint compound). Cut a larger, well-shaped hole around the hole that you are trying to repair, in the shape of a rectangle (for example, if you had a football-helmet shaped hole in your wall, you'd cut around the hole in the shape of a rectangle) and remove the excess drywall. Cut the drywall patch to the same size as the hole you just made. Screw the piece of drywall into the joists inside the hole. Use joint compound to cover the drywall screws and blend together where the drywall patch meets the old drywall. After it had dried, sand it even. Prime and paint.
For drywall repair . bullet patching is cutting out a piece of gypsum board the same size as the hole but leaving all the paper on the face so you don't need tape to finish it - google" Bullet patch drywall" for images
There will usually be a flat rate if a patch can be used to cover the hole. Labor makes up the majority of the project's cost. You can expect to pay approximately $50 to $75 per square foot for minor repairs, or $60 to $90 per hour for handymen. You can contact Patchproflorida if you need drywall repair contractors in Tampa FL.
Replace to inlet washer this normally happens when the washer develops a hole
If there is a rotted hole in the muffler please replace the muffler. However, if there is a small hole at the bottom end of the muffler it is there to allow water to escape.
You will get a better result using drywall mesh cloth, 2 grades about 120 and 180.
cant do it. high pressure line. only repair is to replace line or keep fluid full until repair.