0
no, you have to replace them every time
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the torque for a 1.9 Saturn engine piston rod?
I believe these are torque to yield bolts and the specs are: Initial torque to 19 Ft/Lbs Tighten an additional 75 degrees It's also not a good idea to reuse these bolts as they are stretched when tightened.
What are the connecting rod torque specs for a 2000 Saturn with a 1.9 dohc?
I believe these are torque to yield bolts and the specs are: Initial torque to 19 Ft/Lbs Tighten an additional 75 degrees It's also not a good idea to reuse these bolts as they are stretched when tightened.
Can you reuse the head bolts on a corsa 1.6?
I would not recommend it. The bolts are stretched during the torque procedure.
What are the torque values for the cylinder head of a 1997 24L Pontiac Grand Am?
For all the 2.3, 2.4L QUAD 4 engines, the head bolts are Torque to Yield. The porper torque value is 30ftlbs PLUS a 90 degree turn of the wrench. The bolts must be new every time ( NEVER REUSE OLD BOLTS). The torque values and proper sequence are including in the box the new bolts come with. BUT honestly, the torque value is 65ft lbs like all GM Chevy motors have been for eons.
Can you reuse flywheel clutch torque bolts for Chevy 350?
i have replaced my clutch to 10.5 diemter ,can i re use the morso flywheel/clutch bolts
Can head bolts be reused on Saturn 1.9 DOHC?
No There are torque to yield bolts One time use bolts......spend the extra 20 dollars it will save you a headache in the long run
Cylinder head torque specs for Pontiac grand prix 3.8l?
first get new head bolts. they are torque to yield. torque them to 37 ft-lbs and then rotate an additional 120 degrees.
What happens if you reuse the old head bolts when replacing a head gasket?
The head bolts will not have the same clamping capabilities, since they were stretched on the first installation. You may blow a head gasket due to the bolts losing torque.
What is the torque on Rod Bolts on a 2001 4.7 dodge?
Warning! These are "torque to yield" bolts. Once installed and torqued to spec they yield, or stretch. The bolts, once loosened, cannot be reused. They MUST be replaced with new or they WILL fail. Once you have new bolts, the tightening sequence is 20 ft/lbs, then tighten an additional 90 degrees (exactly one quarter turn).
Should the head bolts be replaced when changing head gaskets on a 2003 Chevrolet Malibu with a 6 cylinder?
If they are torque to yield. That means if you torque it to a certain number and then have to turn it ,say, 90 degrees more. the answer is yes because you are stretching the bolts.
What is the torque and tightening pattern when using old bolts to replace the head gasket on a 1989 Chevy S-10 2.5?
You cannot use the old bolts to retorque the heads. They are torqure to yield bolts. You must get new bolts.
What is the Head bolt torque 1994 Ford Falcon 4.0 engine?
Proper way to torque them is to buy new bolts and do them up via instructions that come with head gasket ( they are torque to yield - from mem 30 ftlb then 180 degrees more , but that's just from mem ). If you are not using new bolts you are better off to just do them to about 40ft lb, 50 , then 65ft lb .Not much use toqueing to yield unless you use new bolts...
