0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Is a 15 watt spider 3 amp good..mostly for a squire strat or maybe an epiphone?
A 15 watt Spider 3 amplifier is for practice, and in that capacity works fine with any good guitar -- including a Stratocaster or Epiphone. For a practice amplifier to use with a bass guitar, you would want to have at least 30 watts -- like a B-DEC 30.
How long will a fully charged 12 volt battery power a 600 watt stereo amplifier?
maybe 30 mins
Purchased the Fender G-30 amplifier and can't use the line out is the amplifier defective?
There's no such thing as a Fender G30.
Can I use a small 30 watt amplifier as a pre-amp?
There is no such thing, 30 watts is 30 watts. "Line in" is normally about 1v peak - to - peak. So if your 30 watt amp has a "line out", no problem. An amp can be modified to have a "line out". Similarly, an amp can be modified to accept larger inputs without damage. However, driving an amp straight from the normal output of an amp, although possible, is fraught with danger and expensive consequence and should be avoided at all costs
Can you plug a 20 watt guitar amplifier line out jack into a 30 watt guitar amplifier input jack to increase the output volume?
No, from what I understand the line out on a guitar amp puts out a hotter signal than an instrument (your guitar for example) and shouldn't be run into another amplifier's input jack. The Line out jack is designed to be run into a PA or a mixer. Your best bet is an A/B/Y box to run both amps simultaneously.
How many lumens in 30 watt led?
1800lumens per watt
What happens if you connect 4 ohms impedance speakers which are 40 w RMS and 200w MAX to a 8 ohms and 30 w impedancece amplifier?
If the amplifier is not rated for 4 ohms impedence, you will quickly over-current the amp, burning out components. The power handling of the speaker and power output of the amplifier does not matter in this case. It must be compatible with the impedence load that you are connecting.
Can you run a 100 watt bulb with low voltage cables?
The cable voltage is set by the voltage of the supply and not by what is connected to it. But a 100 watt amplifier on a 120 v supply would draw less than 1 amp even at high volume.
What type of oil used for UST 3500 Watt generator?
Use exactly what the owners manual recommends and nothing else. More than likely use 10W-30 in the summer and 5W-30 in the winter.
What happens if you connect impedance speakers which are 40 w RMS and 20 0w MAX to a 30 w impedancece amplifier?
This question is slightly confused in its construction. Impedance and Wattage are references to two separate electronic variable measurements.Impedance is the measurement of a coil's reactive resistance to an AC signal and is defined in henry (symbol H). Impedance can also be referenced in ohms (symbol Ω). Industry standard audio speaker input impedance is typically 4 or 8Ω. Audio amplifiers' outputs are also rated for impedance and usually designed to be mated with industry standard speaker input impedances. You want to try to make sure these two values are the same: 8Ω speaker on an 8Ω amplifier, 4Ω speaker on a 4Ω amplifier, or if they have to be mismatched, an 8Ω speaker on a 4Ω amplifier.Wattage is the measurement of the power rating of some electronic component and is defined in watts (symbol W). A speakers' wattage rating is the amount of power it can accept without being damaged. An audio amplifiers' wattage rating is the amount of power it can produce without being damaged. You want to be sure to have a higher wattage rated speaker connected to a lower wattage rated amplifier.For the usage of 40W speakers connected to a 30W amplifier, neither component will be damaged in this configuration. However, if the ratings were the other way around, 30W speaker on a 40W amp, the speaker could be damaged if the amplifiers' power (volume control) is turned up all the way. At the very least, if a 30W speaker is on a 40W amplifier, you will be able to hear distortion at max volume because the speaker is clipping the tops of the higher amplifier power signal peaks.
How many kwh is used by a 60 watt bulb?
A kilowatt is 1,000 watts. A 60 watt bulb uses 60 watts in an hour. So, in half an hour it uses 30 watts. Now if a kilowatt costs 20 cents, what does 0.03 kilowatt cost?
Can you use 40 watt in a fluorescent light in place of a 32?
Yes, the wattage is just the power consumption. A 30 watt Fluorescent will give more or less the same light as a incandescent bulb or 60 watts, which is the limit for your fixture for incandescent bulbs.
