0
Can you wire a receptacle and a two way light switch in together?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?
You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.
Why won't my Light turn off at switch?
Presuming the switch worked at one point and just stopped working it is likely that the switch has failed in a normally closed position. The only other possibility is that somehow you have a wire problem whereby the hot side of supply is connected to the load side of the switch. This could be caused by an exposed wire in the switch receptacle. Suggest you turn off power at breaker and replace switch as a start. When you have the switch removed from the receptacle, with wires still connected see if switch works. If it does it could still be bad, but examine the wires around switch and see if you have any exposed wire that could be touching the load side of the switch (Side connected to the light).
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you wire a light to a switch at the end of a run and which controls an outlet?
Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.
How do you wire a receptacle from two switches one is 3 way one is single pole?
You cannot wire a single pole switch and 3 way switch together.
You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
Can you wire a light switch with only one 14-2 wire?
If the power feed goes directly to a fixture, or if you are wishing to switch a receptacle that is not now switched, you can us a 14-2 NM cable to install a "switch loop", provided the circuit is no larger than 15 amps. To do this, after running the 14-2 NM cable, connect the WHITE conductor of the 14-2 to the hot wire. At the switch, connect the black and white conductors to the switch terminals. At the fixture or receptacle, the black wire of the 14-2 NM cable now becomes your switch leg and is connected to the black conductor of the fixture or brass terminal of the receptacle. The NEC (for the United States) requires that the switch be fed with the white wire and the black wire be used as your switch leg.
How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?
You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.
How do you run a light with a switch from a existing outlet with out controlling the out let with the switch?
Break off the tab that jumps between the wire mounting screws on the side of the receptacle. This turns one receptacle into 2 seperately controlled parts--one is always hot and the other is controlled by the switch (the one with the lamp plugged in).
Why won't my Light turn off at switch?
Presuming the switch worked at one point and just stopped working it is likely that the switch has failed in a normally closed position. The only other possibility is that somehow you have a wire problem whereby the hot side of supply is connected to the load side of the switch. This could be caused by an exposed wire in the switch receptacle. Suggest you turn off power at breaker and replace switch as a start. When you have the switch removed from the receptacle, with wires still connected see if switch works. If it does it could still be bad, but examine the wires around switch and see if you have any exposed wire that could be touching the load side of the switch (Side connected to the light).
Why would an electric receptacle have 3 hot and 3 neutral wires With one set of wires screwed into the sides of the outlet and the other two sets pushed into the back?
no you have to improperly install it....... :P Shut off the power to the receptacle. Now remove the three black wires from one side of the old receptacle and twist them all together with your pliers. Make a short pigtail 6 inches long, same colour and wire size. Now twist this pigtail into the other three wires. Hold all four wires together with the appropriate size wire nut. Do the same with the white wires. Push all the wires into the back of the receptacle box. Connect the two pigtail wires to the new receptacle black wire to the brass coloured screw, white wire to the silver coloured screw. Screw the new receptacle back into the box, install cover plate, turn the power back on. Done deal.
How do you wire two electrical recepticles in one box?
Black is Hot and White is Neutral and there should also be a bare ground wire. One black/white/bare cable is supply for receptacle and the other is connected in parallel and goes to another outlet. You need your ceiling fixture connected to one of the wires coming into the receptacle box, Black to Black, White to White and Bare to Bare. However, assume you want to be able to switch the ceiling light with a wall switch unless there is to be a pull chain on ceiling light. To connect switch run a new wired from the receptacle to a switch and run a wire from switch to ceiling fixture. At original outlet connect as described above. At switch connect White wires together with a wirenut, then do the same for the bare wires. Connect Black wire going to ceiling to one side or switch and Black wire coming from original receptacle to other side of switch.
What is the white cable when connecting to a light switch?
On a light switch the white wire is neutral. All the neutral white wires are tied together under a wire nut and pushed back inside the box. The white is not connected to the switch.
How two wire 2 light switch up in 1 box?
Tie all the white wires together under a wire nut and push them back in the box. Tie the black incoming power wire and outgoing power wire, if there is one, together under a wire nut with a black wire pigtail. Connect this pigtail to one screw on each light switch. Connect the black wire going up to the lights to the appropriate switch you wish to use to control that light.
What do you do with the green wire from a light if the receptacle doesn't have one?
Green typically represents a ground so you would connect to the bare wire at receptacle or look for a green headed screw.
How do you wire a light and switch with the 2 wire old romex?
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
