0
It is the ratio of pulse width to the total time period of a signal.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What gauge of wire from the panel to the outlet would a 240V 52A rated welder require?
#6 You can use number 6 copper if you wish,you will definitely not overload it or you can figure the wire size by the duty cycle. If your welder has a 100 duty cycle rating use wire good for 52 amps or a number 6. If the duty cycle is 90, multiply the amp draw by .95 x 52 or 49.4 amps or a number 8 wire. These are a few more of the duty cycle multipliers 80 duty cycle(.89) 70 duty cycle(.84) 60 duty cycle(.78)Duty cycle takes in to account that most welders do not weld continously at maximum welder output all the time.
What is Duty cycle in mass spectrometry?
First off, the Duty cycle is the proportion of time during which a device or system is usefully operated. For a mass spectrometer, the duty cycle is the part of ions of a particular m/z produced in the source that are effectively analyzed.
Owners manual for ge heavy duty dryer?
four cycle dryer
What is the conductor size for a spot welder draw 90 amp with a duty cycle 40 percent?
It's not so much the duty cycle you have to worry about but the current draw, 8 gauge wire is more than sufficient to hold the current draw of your spot welder.
How many computer outlets can go on a 10 amp circuit?
About 8 amps worth, if you derate the circuit for 100 percent duty cycle.
What is Duty cycle in digital logic?
duty cycle is the total on peeriod in one complete cycle.
What is duty cycle in radar?
Duty cycle is the fraction of time that a system is in an “active” state. ... The transmitter runs for one out of 100 microseconds or 1/100 of the time, and its duty cycle is therefore 1/100, or 1 percent. The duty cycle is used to calculate both the peak power and average power of radar system.
What is the difference between the pulse width and the duty cycle of an injector?
Pulse width is the time in milliseconds that the injector is energized, the duty cycle is the percentage of on-time to total cycle time
What gauge of wire from the panel to the outlet would a 240V 52A rated welder require?
#6 You can use number 6 copper if you wish,you will definitely not overload it or you can figure the wire size by the duty cycle. If your welder has a 100 duty cycle rating use wire good for 52 amps or a number 6. If the duty cycle is 90, multiply the amp draw by .95 x 52 or 49.4 amps or a number 8 wire. These are a few more of the duty cycle multipliers 80 duty cycle(.89) 70 duty cycle(.84) 60 duty cycle(.78)Duty cycle takes in to account that most welders do not weld continously at maximum welder output all the time.
How is width of pulse and power content is related?
The width of a pulse and power are related by a term called duty cycle. Full power means the pulse comes ON and Stays ON continuously for 100% duty cycle. No power means pulse is OFF continuously for a 0% duty cycle. 50% duty cycle means pulse stays ON half the time and OFF half the time. Duty cycle can be used to explain the relationship between pulse and power content.
What is Duty cycle in mass spectrometry?
First off, the Duty cycle is the proportion of time during which a device or system is usefully operated. For a mass spectrometer, the duty cycle is the part of ions of a particular m/z produced in the source that are effectively analyzed.
What is the duty cycle of a docucolor Xerox?
The docucolor Xerox has a maximum duty cycle (number of prints) of up to approximately 200,000 pages per month.
What is the deduction of crane ratings in duty cycle?
50%
The percentage or time a welder can operate without overheating is?
This is called the duty cycle. A machine with a 60 o/o duty cycle can weld continuously for 6 minutes out of 10.
What to do for obtaining 40 percent duty cycle with 555timer is it possible?
Place a diode in the circuit to bypass R2 during the charging cycle.. this will allow you to achieve duty cycles of < 50%
What is the duty cycle of a square wave that is positive for two horizontal divisions and at zero volts for four horizontal divisions?
The duty cycle is (positive time) divided by (total cycle time) = 2/6 = 1/3 or 33.3 %
Who to determine the rms ande the average value of square wave?
RMS is an average. If you have a 50% duty square wave, the average will be 1/2 the peak. for a 33.3% duty cycle, the average will be 1/3 the peak, etc. VRMS = Vpeak x duty cycle
