Flow control vs. congestion control:
Flow control means preventing the source from sending data that the
sink will end up dropping because it runs out of buffer space.
This is fairly easy with a sliding window protocol--just make sure
the source's window is no larger than the free space in the sink's
buffer. TCP does this by letting the sink advertise its free buffer
space in the window field of the acks.
Congestion control means preventing (or trying to prevent) the
source from sending data that will end up getting dropped by a
router because its queue is full. This is more complicated, because
packets from different sources travelling different paths can
converge on the same queue.
Flow Control : control the speed of sender and reciever
Congestion Control: control traffic entry to avoid congestive control. once Congestion occurs the traffic will wait to recover from it.
Flow control may cause a sending network to pause when the receiving network is overwhelmed with traffic. The receiving network can signal the sending network to temporarily stop and then to resume traffic once it gets caught up with the traffic.
Error detection occurs when a receiver has detected a corrupted packet and needs to have it resent.
Flow control refer to the flow of data. Congestion control refers to the flow of data such that there is no traffic or congestion.
Electrical is an one type of energy ie flow of electrons... this flow of electrons constitutes the Electricity which we are using for our use
It's the difference between pressure and flow. The pressure is measured in volts, and the current in amps.Current is the flow of electrons.Power=VIcosϕV=voltageI=currentCosϕ=cosine of angle between V and IAnswerCurrent is a drift of electric charge, expressed in amperes. Power is the rate of doing work, expressed in watts (equivalent to a joule per second).
it will control the flow of electrons between the source and drain,the controlling will be depends upon the input voltage to the substrate.
A resistor is a device designed to detect difference in current and stop the flow of electricity. On most every type of electric engine or circuit has a resistor.
For a current to flow between two points, those points must have a potential difference (voltage) across them.
Average rate will remain same but Flow control: end-to-end mechanism for regulating traffic between source and destination • Congestion control: Mechanism used by the network to limit congestion
The techniques include End-system flow control, Network congestion control, Network based congestion avoidance and Resource allocation.
The difference between datalink layer flow control and transport layer flow control is the need to keep the different layers of data separate in the flow control option.
Flow Control
In congestion control, the load on a network is prevented from exceeding the capacity. Quality of service refers to the characteristics that a flow of data seeks to attain. If there is good congestion control, then the QoS is also good and vice versa.
Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing Where is the following items located in IVP4 header? Congestion Control Differentiated Services/QOS (Quality of Service) Error detection and correction Flow Control "Connection oriented" Queues/Queuing
the difference between flow and motion is well flow is like floating and motion is the way you move
the station window size the congestion window memory buffers receipt acknowledgement
minimize congestion, stability margin improvement, line overload reduction, power flow control
difference between laminar air flow & reverse laminar air flow
what's the difference between flow chart and structure diagrams and pseudo code
Net cash flow is the difference between income and expenditure.