0
Do I need a special screwdriver to remove the rear light housing from your PT Cruiser?
Wiki User
∙ 11y ago
No, they are usually phillips.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is there a special tool used to remove the base of a 2007 Chrysler PT Cruiser antenna?
Yes.
How do you remove tail light for 98 land cruiser?
Removing a tail light from a 1998 Land Cruiser requires replacing the housing seal and unscrew the mounting hardware from the rear end. When the mounting hardware is remove the tail lights will easily come out.
How do you replace 1997 prizm domelight bulb?
Remove the plastic housing with small slotted screwdriver. Gently remove the bulb vertically and replace with new bulb. Replace plastic housing until you hear it click into place
How to remove the dome light in a Ford Explorer?
Steps to remove the dome lightTools neededSmall flat head screwdriverSmall Phillips head screwdriverStepsInsert the flathead screwdriver into the slot and gently remove the plastic cover. (It just pops off)Using the Phillips screwdriver remove the two screwsRemove the wires that lead to the switches and bulbsRemove the housing (you should be to the the trim)Remove the screws to the housing (you should be able to see the roof)Reverse the process to put it back together
How do I change a BMW 328i air filter?
Open the hood and locate the filter housing on the driver's side of the engine towards the front.Unscrew the hose clamp connected to the housing and pull the hose off the housing.Using a screwdriver, push up the tab holding the mass airflow connector to the housing and remove the connector.Using a 10mm socket, remove the two bolts securing the housing to the car frame.Disconnect the other end of the housing from the inlet by inserting a small screwdriver in the tabs and remove the entire assembly from the engine area.Using a T25 bit, remove the (6) torx screws holding the two housing halves together and separate housing.Remove and replace filter.Reassembly is the reverse of the above.
Do you need a special tool to remove the power steering reservoir cap?
There is no special tool needed to remove the power steering reservoir cap of a Volkswagen Golf. It can be removed with a flat head screwdriver.
How do you remove the ignition lock on a 1971 Chevy Chevelle?
# Remove the steering wheel and directional signal switch.It is not necessary to pull the wire harness out of the column # Place the lock cylinder in run # Insert a small screwdriver into the turn signal housing slot.Keeping the screwdriver to the right side of the slot,break the housing flash loose and depress the spring latch at the lower end of the lock cylinder. # Remove the lock cylinder
How do you remove a window switch in a 2002 pt cruiser?
gently pry out evenly on surround shroud. slide red locking clip from wire bundle to release. pull off knobs and remove switch from housing.
How do you remove the crankshaft pulley on a 2002 Chrysler PT Cruiser?
It requires a three jaw puller and a special tool that is inserted in place of the bolt.
How do you remove the spool housing for a Black and Decker grass hog xp model gh 1000 type 4 to attach a grass gator grass blade head?
1. Remove the spool cover. 2. Remove the spool. 3. Use flathead screwdriver to remove the single screw in the center of the housing. 4. Pull. The housing straight off. (Note: it may be somewhat difficult to pull the housing off, but a strong firm pull should remove the housing. No turning is necessary.) 5. Put the new housing on, lining up the center hole on the housing with the center rod on the base. 6. Use flathead screw to replace the single screw into the center of the housing.
How do you remove a front axle assembly on an Acura Vigor?
To remove the driver side cv axle: place a large flathead screwdriver between the transaxle housing and the axle. Then place a chisel behind the screwdriver. The order will be: transaxle housing, chisel, flat screwdriver, axle. Then give the chisel a hit or two with a hammer and it should pop out with ease. I'm not sure about the passenger side axle but I think you may have to take off the pillow block that is bolted to the transaxle which the cv axle sits in.
How do you replace the brake light bulb on a 2001 PT Cruiser?
Access to the brake light bulb is through the tail light lens. First, remove the tail light lens by removing the single star shaped screw that secures the lens. You do not need a special screwdriver or bit: a regular flathead screwdriver will work fine. Once the lens is removed, press in on the bulb and turn ever so slightly. Bulb will now pull out.
