answersLogoWhite

0


Best Answer

i think you cannot reset, you need to buy a new air bag ecu

User Avatar

Wiki User

โˆ™ 2008-10-30 09:47:06
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Does anyone know how to reset the air bag light on 1991 Toyota MR2?
Write your answer...
Submit
Related questions

Where is ECU reset button for a 1991 Toyota cressida?

There is no ECU reset button.


How to reset check engine light 1991 Toyota land cruiser?

try disconecting the battery or pulling the ECM fuse


How do you reset the oil light on a Toyota tercel 1991?

go to your owners manuel, there is a section in there that will tell you or call your local dealer


How do you reset engine Light on 1991 Volvo 240 DL?

how do you reset engine light on 1991 volvo 240


How do you reset the brakelamp light on the dashboard - Honda prelude 1991?

reset the brakelamp light on the dashboard - Honda prelude 1991


How do you reset the check engine light on a 1991 Mercedes Benz 560 sec?

How do you reset the check engine light on a 1991 mercedes Benz 560 Sel


How do you reset the 'service ccr' light on a 1991 Eldorado?

To reset the service CCR light on a 1991 Eldorado, disconnect the battery for 10 minutes. Reconnect it and start the car.


What is the brake light number for a replacement on a 1991 Toyota pickup?

I am looking for the bulb number to replace a burnt out bulb on a 1991 Toyota pickup


Why is the AC light blinking on 1991 Toyota Camry?

If an AC light is blinking on a 1991 Toyota Camry it may indicate that a belt is slipping. The AC light may also blink indicating that the system has been overcharged.


How do you reset your check gauges light in a 1991 Chrysler 5th avenue?

There is no reset for a check gauges light. If the light is on, there is a problem either with the temperature oil pressure or voltage.


How do you reset your check engine light on a 1991 Mitsubishi?

Have vehicle scanned to determine the problem


How do you reset the check engine light on a 1991 range rover?

Disconnect the battery for about 1 min.


About how many miles are left when the fuel light comes on in a 1991 Toyota Cressida?

60 kms


Check engine light 1991 Toyota Cressida?

If the check engine light is on for your 1991 Toyota Cressida, that makes that some repairs need to be made to the engine. Taking the car to a certified mechanic to perform a diagnostic test can confirm if there is any issues with the engine.


How do you reset maintenance required light on a 1991 dodge ram 2500 5.7 l?

Take the bulb out


How do you reset the maintenance required light on a 1991 Jeep Cherokee Laredo?

Unplug or replace maint. timer


How do you reset a 1991 service engine light for a Oldsmobile 1991?

Disconnect the negative battery cable from the battery, wait a few minutes then reconnect it. But, if the reason the light came on isn't fixed, the light will only come back on again.


What transmission came in the 1991 Toyota 4x4?

i have the 1991 toyota 4x4 with a g58 trans


Is a 1991 Toyota 4Runner compatible with a 1990 Toyota 4Runner?

A 1991 Toyota 4runner is bigger than a 1990 4runner


Where do you find the reset button on a 1991 Chrysler new yorker?

A 1991 Chrysler does not have a reset switch.


How do you reset service engine soon light on 1991 Pontiac Bonneville?

remove battery cable for 1 min


Where is the tail light relay located in a 1991 Toyota pickup?

under the dash above left kick pad


1991 Chevrolet s10 blazer warning brake light always on anybody knows?

If a 1991 Chevrolet S10 Blazer warning brake light always stays on, it could just be a malfunction of the light. To reset it, disconnect the battery for 10 minutes.


How do you replace 1991 Toyota tercel right tail light?

open the trunk, and pull back the carpet and there will be 2 nuts holding the light in place. unscrew them and pull the light out.


How do you reset the check engine light on a 1991 4 door Saturn?

You reset the light by unhooking the battery for 30 minutes. But the light will come right back on after a couple of driving cycles. The light is on because the computer has detected a problem with the emissions system. Have the computer scanned and this will help to find out what is wrong.