0
If there is only one plug, try removing the plug, spraying WD40 in the plug hole, replace the plug and try starting.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How do you replace spark plug wires on 2001 dodge neon?
Just like any other spark plug you just need to find the size of the plug and buy it.
How often to replace 2003 Camry spark plugs?
If you do not have any problems with plugs, change them when you replace the timing belt (do not forget to replace the spark plug wires too).
Do you have to change all your spark plugs if you are changing the spark plug wires?
No you do not need to replace any plugs at all when replacing wires.
Does Spark plug wire damage cause hesitation?
Absolutely. Replace any damaged pug wire.
How do you remove the porcelain from the base of the spark plug when it breaks off?
I do not understand why you want to remove the porcelain if it is broken off. Just remove & replace the spark plug which is no longer any good if the porcelain is broken.
How do you replace 1999 ford 250 spark plug?
remove fuel rail and any hoses plus air cleaner
How do you replace the spark plugs on a 2003 Nissan Micra k12?
same as any other car u remove the spark lead from the top of the engine beside the rocker cover then use a spark plug socket (which is longer than a normal one) to remove each spark plug be careful to put the leads back onto the same spark plug you removed and not to over tighten the spark plugs.
What doess cylinder miss fire mean?
It means that for some reason the spark plug did not ignite the fuel mixture and therefore the cylinder that misfired did not produce any power. It is caused by a bad spark plug or a bad plug wire or lead or a bad ignition coil.
What do you need to adjust the gap of a spark plug?
A spark plug gapper. Avalible at any autoparts store
Why would a cracked plug socket cause a fire?
The part that cracks on a spark plug is the insulating material that shields the metal part of the plug that conducts the electrical spark, potentially allowing it to escape or leak and possibly ignite any flammable substances or materials as it grounds itself.
How do you check plug wires?
How to Check a Car's Spark Plug Wires By eHow Cars Editor Part of car overhaul and car maintenance is checking your car's spark plug wires. These cables connect the spark plug to the distributor. You must check them every year and replace or clean them as needed. Always replace the entire set even if only one wire shows signs of wear. Difficulty: Moderately Easy 1. Turn off your car engine to overhaul your spark plug wires. Let your car cool down. Open the hood of your car and look inside for your spark plug wires. 2. Find the distributor. You will see several cables going across and ending at the individual spark plugs. These are the spark plug wires. 3. Remove one spark plug wire at a time for better inspection. Pop it off the spark plug and the distributor. Remove only one wire at a time. This will ensure you do not mix up the spark plug wires. 4. Look at the wire carefully. If it has any tears or cracks, you must replace it now. Always replace all spark plug wires at the same time even if only one needs replacement. 5. Clean a dirty spark plug wire. Use hand cleaner soap and wipe completely dry. Reinstall the spark plug wire into the distributor and connect to the spark plug. 6.Repeat this overhaul at least once a year. Remember to check the spark plug wires when you change your spark plugs. Tips & Warnings · Do not remove all of the spark plug wires at one time unless you are very sure you know which one goes where. If you mix them up, your car will not run. Remove one at a time then replace or reinstall it. Move on to the next one.
How do you replace the spark plugs in a Toyota Corolla?
same way you replace them in any other 4 cyl. car. Take the plug wires off of the plugs (make sure to keep them in order to be put back on exactly the same or your cylinders will not fire in the correct order), use spark plug socket (the kind with a rubber insert inside it to keep from breaking the delicate porcelain) to remove plugs, replace with new ones, making sure not to overtighten them as that will only make things difficult next time you remove them, and reattach the plug wires EXACTLY as they were. If you cant see your spark plug wires when your hood is open you need to remove the enigne top cover.
