0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is fault code 44 on a 1987 S10 with 2.8 liter engine?
O2 sensor circuit (lean exhaust) 1) O2 sensor defective or lead shorted 2) Lean injectors (dirty or blocked) 3) Water in fuel 4) Exhaust leaks upstream of O2 sensor 5) Fuel pressure or volume too low 6) MAF sensor reading lower airflow than is actually present 7) Vacuum leaks 8) Incorrect or poorly calibrated PROM
Where can you find the Knock sensor on a 1991 Oldsmobile cutlass calais?
If it is a quad 4, the knock sensor is on the firewall side of the engine, at the transmission end of the engine, just below the exhaust manifold. It has a single lead and is about 2" in diameter and 1-1/2" high. Use a proper fitting socket or wrench to unscrew it.
Why am I getting 43 code on 89 Chevy Celebrity 2.87 V-6 when we have replaced ECM O2 sensor and TPS where and what is the ecs unit?
To attempt to answer your question I looked up the code 43 in my Factory Service Manual. The full answer and diagnostic procedure is much too long and involved to try to post in this format. If you don't have a manual you might be able to use one at a local library. But to give you some level of answer: Code 43 has to do with the knock sensor to ECM circuit. ECS should be ESC which is electronic spark control. The book suggests that the problem could be in the knock sensor, the ECM, or the wiring and connections between the two. Since you have replaced the ECM it would seem that the wiring and knock sensor remain POSSIBLE problems. Look particularly at the connector to the knock sensor. Corrosion or oil contamination in the joint is a possible problem. If not then the knock sensor would be the next check. The book says to connect an ohm meter between the terminal on the knock sensor and ground on the engine block. The resistance should be between 3300 and 4500 ohms. If it is not between those numbers then the book says to replace the knock sensor. The knock sensor screws (pipe thread) into the side of the block nearest the firewall, and goes to water coolant passages. If you take it out it could lead to coolant loss so have a suitable container ready to catch it. It is not in a convenient place to get to. Another thought: The knock sensor grounds on the pipe threads. Corrosion or contamination there could also be a problem. If you take the knock sensor out or replace it don't use thread sealant as it could interfere with the ground.
How do you replace the knock sensor in a 2003 Toyota carolla?
Should be on the side of the engine block with one bolt and wire harness. Make sure you really need this as they are not cheap! Make sure your fuel is good your sparkplugs are in good shape, (iridium ngk). Make sure your timing is correct. If all of this is correct and you are still getting a knock sensor code then you may need to replace it. Note: they do not usually go bad. The cause of the code problem is usually not the knock sensor itself, but the signal wire between the knock sensor and the external connector by the intake manifold. This wire gets brittle if it is overheated. Removing the connector during disassembly can break the signal wire inside the shield. Obviously, that prevents the signal from getting to the PCM. We advise techs to replace this short length of knock sensor lead wire any time the intake manifold is removed. Especially if it’s been overheated. A quality Knock Sensor is more important than ever thanks to todays increasing gas prices. Your Engine Knock Sensor enables your vehicle to obtain the optimum combination of timing and fuel/air mixture to generate power and efficiency and that means less wasted gas. In addition to robbing you of fuel economy and performance a faulty Knock Sensor can cause expensive damage to your engine. Remember, the Knock Sensor keeps fuel from detonating in the cylinder, exploding rather than quickly burning as it should. If not replaced a faulty Knock Sensor can quite literally cause hundreds if not thousands of dollars in damage.
How does sewer leaks damage the environment?
Sewer leaks damage the environment by letting filthy waters either leak into our water pipes therefore poisoning our tap water or leaking out to sea or a larger body of water causing dirty water there. This could lead to the death of many marine life, including native fauna.
Are knock knees related to osteoarthritis?
No they are not, However if they are not corrected they can lead to it.
Picture of knock sensor on 1999 Chevy cavalier z24 of location?
I can't upload photos on this sensor, because it is very hard to see. It is located below the heater tubes that lead to the heater core. On the 99 model it is bolted into the engine block with 1 bolt going through the center of it, and the sensor is round, with a wire, and is about the size of a standard lug nut. You may need a mirror on a stick just to see it. I would still be interested in a picture. Thanks go to autozone.com type in knock sensor in the product search, then year,make model. There is a photo there.
What happens when a toilet leaks?
A leaking toilet can lead to water damage to the flooring and surrounding areas. It can also waste a significant amount of water, causing higher water bills. If left unresolved, it can lead to more serious issues like mold growth and structural damage.
What is in your water that stains sink blue-green?
Probably copper. This may be caused by your water being acidic and reacting with the copper in your pipes. You may have to get the pH of your water tested if it below 6 then the water is too acidic. Although small amounts of copper in your water is not harmful to your health corrosion in your pipes may eventually lead to leaks.
Changed wires and spark plugs on 1995 Dodge Intrepid 3.3 and engine still idle rough. Any ideas?
you could need to have the emissions (vaccuum) system inspected or inspect yourself for leaks (find the vacuum pump and apply vacuum lead down pump with gauge to see if there are any leaks) other than this there could be an issue with any number of sensors such as the mass air flow sensor, intake air temperature sensor, crank shaft position sensor, throttle body positions sensor, manifold air pressure sensor and many more. another issue could be something such as timing, the timing belt.chain could need replacement (check your mileage vs the owners manual) it could also be a catalytic converter or the oxygen sensor, you can check your o2 sensor using a blow torch and a volt meter to either measure voltage output or the votage resistance as heat increases.
Does lead leach out of glass water pitchers?
No, water will not leach the lead from lead glass.
Is it good or bad to have highly reactive metal in your kitchen plumbing?
It is generally bad to have highly reactive metal in your kitchen plumbing because this may cause oxidization or degradation of the plumbing, which may lead to contaminated water and/or leaks.
