0
Does the muffler inlet and outlet have to be the same size as the tubing?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which is Fuel pump inlet and outlet?
Inlet line will be bigger then the outlet line. on the contrary on my motorcycle fuel pump, the inlet and outlet are the same size!
How do you use a quick disconnect tool for fuel lines?
position/clamp the tool over the inlet flow tubing. hold tightly and push in towards the fuel filter to unlock the plastic clip of the pressure hose. pull the outlet clamp/lock up off and out of the way on the outlet side. perfom same procedure as the inlet side to disconnect it.
For the same size of pipe when mass flow rate is also same what will happen to the pressure drop if change in inlet pressure takes place?
If you change the inlet pressure, you outlet pressure will also change dramatically.
How to change a muffler on Chevy S-10?
First off, crawl under the truck and see if your present muffler is welded on or clamped on. If it's welded on you will need to get an exhaust cutting tool from like Autozone and cut the old muffler off BUT before you do, get your new muffler and measure how far the inlet neck is and outlet neck is on the new muffler and this will tell you how far to cut. You could hold the new muffler up to the exhasut and mark how far from the muffler you need to cut. This is assumign you are replacing the bad muffler with a new one of the same size. Now there is an inlet pipe and and out let pipe on the muffler. You will also need to have the right size clamps. Pu tone clamp on the exhaust pipe going to the engine, then push the exhaust pipe into the inlet end of the muffler and slide the clamp down and snug it up but do not tighten it. Put the other clamp on the exhaust pipe towrd the rear of the truck, push the exhasut ipe into the outlet end of the muffler and then slide the clamp down onto the joint and snug up. if everythign aligns right, then tighten the clamps. Sometimes if you overtighten the clamps you will have exhaust leaks. If you cannot get the joints to seal, you may need to get your system welded. If you exhaust is leak free then you are done. After a few hot and cold cycles you may just want to crawl back under and check the bolts on the clamps just in case they came loose from the heat and cold cycles.
Should the cold-water inlet and hot-water outlet be the same size on a 50-gallon electric water heater?
The inlet and outlets are the same size on a tank, weather your plumbing is the same size should be the question. This is not critical, but they should be the same,if there is no backflow restrictor on a plubic line and the inlet is larger then the outlet,then you could be pushing hot water into the pubic line. New installs recommend an expansion tank,but few people install them,unless they get water hammer,knocking sounds. But most new water heaters have a restrictor built into the inlet. There is no difference between gas and electric, the water does not know how it is being heated.
Which pipe is the outlet and which is the inlet of a heater core?
It hard to generalise, but.... Generally the inlet pipe comes off fairly close to the thermostat/water pump, and the outlet returnes the water somewhere not near the thermostat/water pump. start the engine and feel the 2 heater core lines the one that starts to get warm first is the inlet. As far as the heater core itself, usually the smaller of the two tubes or the lower one is the inlet. If they are both the same size and are side by side it probably doesn't matter.
How do you bypass the heater core on a 1999 Ford Expedition XLT 4.6?
There are two heater core hose that goes to the firewall the inlet and outlet. through that hose, you will also have the rear heater core hose attached to a T joint in both the inlet and outlet hose. You splice the hose of the front heater core inlet and connect that to the rear heater core inlet hose. Same goes to the Outlet hose with the T joint using a conncetor which you can buy at your auto parts store, 3/4 inch size. Basically you are bypassing the front heater core that is connected to the firewall. You wont have any defroster and heater for the front, but the rear vents and control will have heat.
What is single stage compressor?
A single-stage compressor is a type of compressor that compresses gas or air in a single step, raising its pressure from inlet to outlet in one operation. It is more commonly used in applications where a moderate increase in pressure is required, such as in residential air conditioning units or small workshop tools.
How do you change a catalytic converter on a 1984 Nissan Sentra?
The install is the same as a muffler. A muffler shop can do it cheaper than anyone else.
Does Orlando still have a Capezio dance outlet?
Yes, is in the outlet mall. The same one with the nike outlet
Will a Honda 2006 250ex muffler fit on a 2003?
The muffler from your 2006 Honda 250 will fit on your 2003 Honda 250. The mufflers are in exactly the same.
Where is the fuel filter located on a 2003 GMC Envoy?
Underneath the vehicle on the driver's side. The inlet and outlet fuel hoses are on the same end of the filter and are attached with quick connect fittings. The filter is about 2 inches in diameter and about 3 inches long.
