0
Inlet line will be bigger then the outlet line. on the contrary on my motorcycle fuel pump, the inlet and outlet are the same size!
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Which outlet on fuel pump is supply and which one goes to carb?
The pump should have a marking on it in the form of an arrow, "to carb" or "carb", or an "in" & "out" on it near the inlet and outlet ports (normally the bottom but depends on the mfg of the pump).
How to replace a fuel pump in a 1984 camaro?
CARBURETED MODELS # Disconnect the negative battery cable # Remove the fuel inlet and outlet lines.Use two wrenches to prevent damage to the pump and connections # Remove the fuel pump mounting bolts and the pump and gasket
Fuel pump line locations for 1986 suzuki samurai?
If you are looking at the fuel pump from the top with the two parallel lines pointing away from you and the 3rd line facing left, the right of the two parallel is the inlet the left one of the two parallel is the return. The 3rd hose facing left is the outlet hose. return | | inlet outlet _______
What is manometric head?
it is the pressure difference between inlet and outlet of pump.
Where is the fuel pump located on a 1974 Cadillac eldorado?
The fuel pump for the Cadillac Eldorado with 500 ci engine is located on the left side of the engine block. There are two bolts that hold it in place. There is the fuel line from tank ( fuel pump inlet) line , vapor return hose and fuel pump to carburetor line( fuel pump outlet.) 1974 fuel pumps also have a fuel filter in the pump.
Is there a right and wrong way to install a fuel filter?
Yes, there is an Inlet and Outlet. From the fuel tank, the fuel enters the inlet side and exits from the outlet side. The filter should be marked or possibly have different size connectors.
Why do arteries take blood away from heart?
The Circulatory System of the body is a simple plumbing system with a central pump, and a bunch of pipes that carry the Fluid around. The pump (heart) has an outlet and an inlet. The arteries are connected to the pump's outlet and the veins are connected to the pump's inlet. So, there you have it.
On a fuel filter the out intlet goes to the motor?
Yes. Inlet is from the fuel tank, outlet is going to the engine.
What happens when matchstick is places in the fuel engine?
It will clog the fuel pump inlet.
What direction does the fuel filter go?
Depending on the fuel filter, it will either have an arrow or be label inlet and outlet. The arrow should be placed pointing away from the tank. Those labeled inlet and outlet will only attach in the correct direction.
Where is the thermostat located on a 2001 Chevy Suburban?
# Standing in front of the vehicle it's on the left front side of engine kind of low. # Be sure to get a gasket as well. # Drain the cooling system. # Loosen the air cleaner outlet duct clamps at the following locations: #* Throttle body #* Mass airflow/intake air temperature (MAF/IAT) sensor # Remove the radiator inlet hose clip from the outlet duct. # Remove the air cleaner outlet duct. # Reposition the outlet hose clamp at the water pump. # Remove the outlet hose from the water pump. # Remove the water pump inlet bolts. # Remove the water pump inlet and thermostat from the water pump. Water pump inlet/thermostat assembly locationTo install: # Install the thermostat and water pump inlet to the water pump. # Install the water pump inlet bolts. # Tighten the water pump inlet bolts to 11 ft. lbs. (15 Nm). # Install the outlet hose to the water pump. # Position the outlet hose clamp at the water pump. NOTEImportant: Align the arrow at the throttle body end of the duct with the throttle body attaching stud.# Install the air cleaner outlet duct. # Install the radiator inlet hose clip to the outlet duct. # Tighten the air cleaner outlet duct clamps at the following locations: #* Throttle body #* Mass airflow/intake air temperature (MAF/IAT) sensor # Tighten the air cleaner outlet duct clamp screws to 62 inch lbs. (7 Nm). # Fill the cooling system and check for leaks.
How do you Replace a house water pump?
first disconnect all electrical supply to pump and then detach the pipe or pipefittings joined with pump's outlet and inlet.
