Fly wheeling or ringing is a process where by circulating current will cause a ringing effect where that is useful is on SCR circuit to reverse power for a shot time enough to reduce holding current therefore shutting the device off
oscillator needs positive feedback in order to produce the undamped oscillations .This is done with help of he amplifier circuit.The oscillations are produced by the tank circuit cosisting of inductor and capacitor.The output of this tank circuit is fedback to the transistor which amplifies it and give back to the tank circuit input.If the gain of the circuit consisting of tank circuit and amplifier is more than one and the feedback given to tank circuit is in phase then we get undamped scillations as the output.
it is the tank circuit
very low current
An inrush current preventing circuit includes a rectification circuit, a temperature-sensitive component, a controller, a switching circuit, and a tank circuit. The controller outputs a control signal to turn on the switching circuit in response to the tank circuit being at a substantially full voltage, and the rectification circuit and the switching circuit forming a current loop for providing power from the rectification circuit to an electronic device. The controller outputs no control signal to turn off the switching circuit in response to the tank circuit being undercharged, and the rectification circuit and temperature-sensitive component forming a current loop for providing power from the rectification circuit to the electronic device for protecting the electronic device. the rectification circuit and the switching circuit forming a current loop to provide power from the rectification circuit to the electronic device;wherein the controller does not output a control signal to turn off the switching circuit in response to the tank circuit being undercharged, the rectification circuit and temperature-sensitive component forming a current loop to provide power from the rectification circuit to the electronic device such that an excess amount of current is prevented from flowing to the electronic device
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
Trim on a ship
Series circuit Parallel circuit Tank circuit
oscillator needs positive feedback in order to produce the undamped oscillations .This is done with help of he amplifier circuit.The oscillations are produced by the tank circuit cosisting of inductor and capacitor.The output of this tank circuit is fedback to the transistor which amplifies it and give back to the tank circuit input.If the gain of the circuit consisting of tank circuit and amplifier is more than one and the feedback given to tank circuit is in phase then we get undamped scillations as the output.
it is the tank circuit
traditionit is often used (like a storage tank for water is) to store resonant energy in AC circuits.
very low current
A series resonant circuit has it's reactive components connected in series with each other; while the reactive components, as in a "tank" circuit, are connected in parallel with each other. The resonant series circuit has the capability of producing usable increased voltage levels across each component at resonance, while the resonant tank circuit does not. The resonant parallel, or "tank" circuit; has the dual capability of creating a situation whereby the input amperage level is reduced to minimum while, at the same time, a maximum amount of circulating amperage is created between the two reactive tank components at resonance.
we use the tank network in AM radio curcite because we get the resonens frequncy.
A tank circuit is used on a radio transmitter. It is an electronic circuit that is used to tune a specific frequency. The tank is made up of two components, an inductor and a capacitor. The two components are connected in a parallel with each other. This is where the term "tank" comes from. Used in a radio transmitter, it is tuned for maximum RF (radio frequency) output on the frequency the transmitter is tuned to.
An inrush current preventing circuit includes a rectification circuit, a temperature-sensitive component, a controller, a switching circuit, and a tank circuit. The controller outputs a control signal to turn on the switching circuit in response to the tank circuit being at a substantially full voltage, and the rectification circuit and the switching circuit forming a current loop for providing power from the rectification circuit to an electronic device. The controller outputs no control signal to turn off the switching circuit in response to the tank circuit being undercharged, and the rectification circuit and temperature-sensitive component forming a current loop for providing power from the rectification circuit to the electronic device for protecting the electronic device. the rectification circuit and the switching circuit forming a current loop to provide power from the rectification circuit to the electronic device;wherein the controller does not output a control signal to turn off the switching circuit in response to the tank circuit being undercharged, the rectification circuit and temperature-sensitive component forming a current loop to provide power from the rectification circuit to the electronic device such that an excess amount of current is prevented from flowing to the electronic device
it is the circuit that is responsible for producing oscillation.In hartley it is two inductors connected in series and a capacitor parallel to this series connection.Without tank oscillator tends to act as as an amplifier.
The LC circuit, or tank circuit, is most commonly located in radios. Its function is to tune radio transmitters to a specific station. The LC circuit consists of an inductor (L), and a capacitor(C), hence the term, LC circuit.