you set your seat to your required position hold driver #1 button till you hear it beep twice and it is set.
To reset a Craftsman garage door opener 1/2 HP, locate the "Learn" button on the opener motor unit. Press and hold this button until the indicator light blinks. Then, press the remote control button you want to program. The opener should now be reset and ready to use.
To reset the driver seat in a Mercedes C320, first, ensure the vehicle is on or in the accessory position. Locate the seat adjustment controls on the side of the seat and press the “reset” button if available, or move the seat to its desired position and then hold the memory button (usually numbered 1 or 2) until you hear a confirmation sound. If your model doesn’t have a reset feature, adjusting the seat to your preferred position should automatically save it. For further assistance, consult the vehicle's owner's manual.
1.) Press the TRIP/RESET button to cycle to "SETUP MENU HOLD RESET". 2.) Now press and hold the button for 2 seconds until "RESET FOR SYSTEM CHECK" is displayed, then release. 3.) Imediately press and hold button for 2 more seconds until "Oil 100% RESET IF NEW" is displayed, then release. 4.) Imediately press button once to display "HOLD RESET IF NEW OIL" and release. 5.) Imediately press and hold button for 2 seconds until "OIL LIFE SET TO 100%" is displayed.
1.) Press the TRIP/RESET button to cycle to "SETUP MENU HOLD RESET". 2.) Now press and hold the button for 2 seconds until "RESET FOR SYSTEM CHECK" is displayed, then release. 3.) Immediately press and hold button for 2 more seconds until "Oil 100% RESET IF NEW" is displayed, then release. 4.) Immediately press button once to display "HOLD RESET IF NEW OIL" and release. 5.) Immediately press and hold button for 2 seconds until "OIL LIFE SET TO 100%" is displayed.
press the reset button... and prey
1. Turn Switch --#2 Position.(just Before Start) 2. Press Odometer Button Twice. 3. Turn Switch --0 (off) 4. Press And Hold Odometer Button 5. Turn Switch--#2 Position 6. Continue To Hold Odometer Button Until Signal & 10k Will Appear.
1. Make sure your trip odometer is on Trip A. 2. With the car turned off, press and hold the "Reset" button for the trip odo. 3. Foot off the brake, press the start button twice while holding the reset button and wait for it to reset.
The button on the steering wheel marked "step" changes the odometer to trip 1 and trip 2. You can also reset these 2 different trips to zero as needed. When you press the trip button multiple times, you will also get the outdoor temperature.
I have a '91 Corolla DX (which I love). -To reset the hour, you have to push the "H" button. -To reset the minutes, use the "M" button. -If you push the "SET" button, it will reset the time to the nearest hour, according to what the display already shows. If the clock shows between 1:01 and 1:29, pushing the "SET" button will change it to 1:00. If the clock shows between 1:30 and 1:59, the "SET" button will change it to 2:00. - Every time the battery is disconnected, the clock will go back to 1:00 and need to be reset.
insert key to position 1 hold odometer reset button (the one on right) holding the button down without letting go turn key to position (2) stay holding button 4 10 secs service light will blink and turn off Make sure 1: The odometer reset button is in T1 (trip one) as the have a t1 and t2 mode both and 2: let go of the button while the light is still blinking. Otherwise it will not reset.
To reset the door code on a 1999 Ford Expedition, first locate the keypad on the driver's side door. Enter the factory set code (usually found in the owner’s manual or on a card in the glove compartment). Once entered, within five seconds, press the "1/2" button, then enter your new five-digit code. Finally, press the "1/2" button again to save the new code.
It's at the parts store in the form of a new pump The is no reset button but there is 2 fuses in the fuse panel under the hood One for start and 1 for run