answersLogoWhite

0


Best Answer

Begin by removing the cover to your 1996 Chevy Suburban CD player. Remove the CD player retaining bolts. Remove the wiring harness from the back of the CD player. Reverse the process to install your new CD player.

User Avatar

Wiki User

โˆ™ 2014-11-20 03:37:23
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How Do you Replace a Slave CD player in a 1996 Chevy Suburban?
Write your answer...
Submit
Related questions

How do you replace the slave cylinder in 96 Chevy C1500?

How do you replace a slave cylinder in a 96 chevey k1500


How do you change a clutch slave cylinder on a 1988 Chevy S10 Pickup?

You will need to remove the transmission to replace the clutch slave.


Do you have to remove transmission to replace slave cylinder in 1999 Chevy 4x4 z71?

YES you sure do.


Where is the slave cylinder located on a 2000 Chevy S10?

The slave cylinder is inside the trans. If you need to replace it you will have to pull the trans out. Its not that bad, its a afternoon though.


How do you change slave cylinder on 2002 Chevy truck?

You will have to REMOVE the transmission and when you look in the bell-housing you will see the slave cyclinder. Remove the 4 bolts that hold it in place and replace it.


How do you remove and replace the clutch cylinder on a 1999 Chevy s-10?

To replace the slave cylinder on this vehicle you will have to remove the drive shaft and then the transmission. The slave cylinder will be bolted to the inside of the bellhousing. The transmission is very heavy so be very careful.


Do you have to remove transmission to replace slave cylinder 97 Chevy 4x4?

YES you do. It's all in the bell housing. No other way to get to it.


How do you replace slave cylinder on 1998 Chevy S10 manual transmission I have been told I need to replace the entire transmission. Is this true?

The transmission must be removed, and put back in, not replaced.


Where is slave cylinder located on a 2000 Chevy s10?

i have an s-10 myself and need to replace that too,but to answer your question i was told it is inside of the transmission.


How do you replace internal slave cylinder on 98 Chevy s-10?

You will need to remove the transmission and you will find it in the bellhouseing. There will be 4 10mm bolts that hold it on,


How do you change hydraulic clutch in 99 Chevy s10?

Which part do you want to replace? The slave cylider or the master cylinder? The hydraulic line and master cylinder.


How do you adjust the clutch on an 89 Chevy 2500?

You can't, there is no adjustment. Time to replace clutch, slave cylinder or clutch master cylinder. 1 of the 3.


How do you replace the clutch slave cylinder on a 1989 Jeep Wrangler?

How do you replace the clutch slave cylinder on a 1989 jeep wrangler


How do you replace the slave cylinder on a 1995 dodge neon clutch?

How do you replace a slave cylinder on a 1995 dodge neon clutch


Can you just replace the slave cylinder on a 1995 Chevy Cavalier?

Pull or cut the hose off the slave and master Cylinder.Go to the parts store and buy a long hose for a grease gun and a couple clamps. Clamp it on both ends and bleed it


Can you replace the starter on a 93 Chevy z71 without removing the slave cylinder?

yes,of course- starter has 2 main mounting bolts,and some wiring looms


Replace the slave cylinder in a 1994 ford f250?

HOW DO YOU REPLACE THE SLAVE CYLINDER ON A 1994 f 250 2 WHEEL DRIVE


When replacing clutch do you also change the slave cylinder?

The slave cylinder is usually replaced during a clutch replacement. The slave unit is fairly inexpensive but the labor can be costly since most vehicles require the transmission to be removed to replace the slave. Since the transmission has to be removed to replace the clutch anyway, there is no extra labor involved to replace the slave.


Where is the Jeep Wrangler slave cylinder?

how to replace the slave cylinder on a 1993 jeep wrangler


How do you replace the clutch slave cylinder on a 1996 C2500 Chevy Cheyenne 350 motor w 5 speed manual tran do you have to remove the trans?

Yes you do. It is inside of the bell housing.


How do you replace the OEM slave CD player in a 1999 Chevrolet Tahoe?

Check with the dealer, or a salvage yard. Even one of the online auction sites.


How do you adjust the slave cylinder on a 1989 Chevy pickup 1500?

There is NO adjustment, You must replace the clutch set to bring the pedal back to the right position. You also need to make sure the clutch slave cylinder/ master cylinder is good before replacing clutch assy.


Do you have to remove transmission to replace slave cylinder on 5.7 1997 5 speed Chevy truck?

YES. It will have 3 bolts that hold it in place in the bell housing. Must remove transmission to service.


How do you replace the slave cylinder in a 1988 ford F150 6 cylinder fwd?

you just replace it


How do you replace a slave cylinder?

to answer your question i need more info such as what type or model car is it and is it a clutch slave cylinder

Study guides

๐Ÿ““
Create a Study Guide