answersLogoWhite
Headlights Tail and Brake Lights
GMC Envoy
Lincoln Navigator
VW New Beetle

How Do you replace back up light bulbs on a 98 Navigator?


Top Answer
User Avatar
Wiki User
Answered 2008-01-11 23:18:38

There are two screws on the inside of the rear lift gate where the handle is on the inside. Remove those two screws. Then by the piece that locks down the lift fate are two plastic clips remove these two. then pull down a little on the plastic rugged panel to expose more plastic clips. With a long screw driver pull down to remove on both sides until you see the light socket. Turn the socket and remove the bulb to replace. install in reverse order. good luck

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

How to Replace Volkswagen polo brake light bulbs?

To replace the brake light bulbs on a VW Polo, pull away the carpeting in the trunk, unscrew the bolt holding the lights on, and disconnect the wiring. Replace the bulbs, put the wiring and bolts back, then replace the carpeting.


Replace tail light 2004 Mitsubishi endeavor?

Take 2 screws out and pull light straight back, it will come over, replace bulbs and put back on and replace screws


How do you replace headlamps on a 2000 Accord?

The bulbs unscrew counterclockwise from the back of the light assy. Sometimes you ave to remove the light to get to it.


How do you replace the headlight bulb located on a 2000 Chevy Malibu?

The bulbs unscrew from the back of the light assy. sometimes you have to remove it to get to the back.


If a back tail light goes out and you replace one of the bulbs but the lights still do not come on does a fuse need to be replaced?

Check the ground on the light.


How do you replace the front running light bulbs on a 94 Saturn SC2?

Open the hood as the light bulb pop into the back side of the lens


How do you replace the charge indicator lamp on 1992 Thunderbird?

take out instament cluster and all light bulbs are on the back


How do you get to the rear brake light bulbs on a 1999 Nissan Frontier?

You have to unbolt the entire tail lamp assembly to change the bulbs. Unbolt the tail lamps from inside the corners of the bed, replace the light bulbs, bolt the tail lamps back in place.


You replace all the tail light blubs on your 94 Lexus es300 and when you step on the brake the dash light come on?

incorrect resistance of light bulbs installed. causes electrical feed back. replace all bulbs with factory replacement Also check that the tail light ground is ok. If the tail light bulbs aren;t grounded, it causes a backfeed of power to the dash lights and causes them to turn on.


Why does this happen Brake lights and turn signal not working in back?

It sounds to me like your bulbs are out. These bulbs have a lifespan just like the light bulbs in the lamps that you have at home. These are easy and cheap to replace, and you can usually access the bulbs from your trunk, if you own a car.


How do you change the 3Rd brake light in a 2001 intrepid?

You must first remove the Trunk liner back far enough to get to the light cavity. There are two bulbs that make up the center third brake light. Just twist the light out of the lock position and replace the bulbs with appropiate replacements and then screw back in.


How to replace a tail light on a 1994 Pontaic Sunbird?

Remove the nuts so you can take the assembly off. Replace the assembly with the new light bulbs and socket it together. Screw the nuts back on to secure it.


How do you replace a broken tail light cover on a 2001 Ford Taurus?

pull back carpet around the taillight. It should be three plastic caps that unscrew and pull the light out, disconnect the bulbs. Replace with a new tail light.


What would cause no back-up light and turn signals to light up from back-up lights and all bulbs are new?

Repair or replace your reverse, neutral safety switch.


How many light bulbs are in the the back of the gauges in a 96 grand am gt?

there are 5 bulbs in the back of the guage panel


How do you replace tail light bulbs in 2005 Nissan Pathfinder?

lift open rear door, unscrew two screws, pull out light assembly straight back, but not to far because wires for light bulbs does not extend long. take your time ,simple job.


What would cause some dashboard lights to work but not others?

Replace the light bulbs that are burned out, usually from the back side of the instrument cluster.


How do you replace tailights in a 2002 Pontiac Sunfire?

Do you mean the tail light assembly, or the bulbs? Bulbs are easy. I can't speak exactly to the 2002 model, but on most of them, from inside the trunk, you peel the carpet that covers the tail lights back, unscrew the bulb holders from the tail light assemblies, remove the dead bulbs, replace the dead bulbs, screw the bulb holders back in, reposition the carpet and you're done. Tail light assemblies are a little more difficult, but not much. They too, should be pretty direct. Holler if you need more help. FriPilot


How do you replace the tail light bulb on a 2002 Hyundai Santa Fe?

take the two screws out. the back of the light is connected with a rubber plug un hooked it an pull off the light,twist the bulb out of the scoket. my advise replace all thre bulbs


How do you change the rear bulbs on a 307?

there is 1 nut & bolt in the boot that has to be loosen, then once undone, take back light off, then replace bulb


Can you recycle halogen light bulbs?

Halogen light bulbs are a type of incandescent light bulbs and are filled with a halogen gas. The halogen gas gives the bulbs a longer life than traditional incandescent bulbs because it helps redeposit the evaporated tungsten back to the filament. Halogen light bulbs are not the same thing as compact fluorescent light bulbs (CFL bulbs), which have mercury inside and are often subject to state or local disposal regulations. Also, halogen light bulbs are not recyclable like CFL bulbs are.


How do you remove the dashboard on a 1997 Volvo 850 in order to replace the bulbs?

Unscerw the dash board, replace burnt bulbs, screww back dash board


How do you replace 2006 Cobalt rear turn signal bulb?

Pull the carpeting back in the trunk by the light that needs replaced and there are 3 or 4 twist nuts that have to come off and then the complete rear light assembly will come out and you can replace the bulbs.


How do i replace third brake light on 2003 olds alero?

You will need a Torx T15 driver and however many 921 bulbs you have burned out. There are 3 bulbs in the center high-mount brake light assembly. Remove the 3 Torx screws right on the face of the plastic bar and the assembly, with the 3 bulbs mounted, comes down. The bulbs pull straight out of their sockets. Push the new bulbs into the blade sockets. Put the assembly back in place and replace the 3 screws.


How do you replace the brake high mount stop light bulb in a 1993 cadillac deville?

There are actually 3 bulbs (GE #1141). On my De Ville there is a small compartment on the rear dash directly in front (from inside the car) the high mount brake light. Simply open the compartment and pull back the trim exposing the 3 bulbs, replace any or all nonworking bulbs.


Still have questions?