0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Must wires be connected to breaker box?
It should be connected to circuit breaker. Circuit breaker will automatically discontinue the flow of electricity if it detects faulty condition.
SMy Breaker box is tripping one of my 20A's How many times can I just reset it before I have to shut it down?
If you have contineous tripping on a breaker then there is a fault on the load of that breaker. Don't reset it any more. What is the breaker connected to?
Where is the circuit breaker for a hot water heater?
The best way to determine which circuit breaker is for the water heater is with a voltage meter, It is suppose to be only one circuit breaker, but in a faulty application it could be two breakers
What is the difference between a 100 amp breaker box and a 125 breaker box?
The amperage capacity of the main bus bars and the connection of the main breaker to the bus bars.
Is it ok to change a breaker box in a house from 2 fuses at 50amps to one at 50 and one at 35 amps?
Breaker boxes do not have fuses associated with them unless the main disconnect is independent from the breaker box. If that is the case both fuses have to be the same in the main disconnect that protects the breaker box.
What is the wire that runs from the electric meter to the breaker box called?
Service Entrance Conductors.
What is a circuit breaker connected in?
it is connected in a box
How do you ground your meter box to your breaker box?
The grounding is done through the metal nipple that connects out of the back of the meter base and into the back of the breaker panel.
Must wires be connected to breaker box?
It should be connected to circuit breaker. Circuit breaker will automatically discontinue the flow of electricity if it detects faulty condition.
How many wires can be connected on to a 20 amp breaker in NH?
Code only allows one wire to be connected to a single pole breaker. Any additional circuitry has to be done in a junction box downstream from the breaker.
The electric meter for a new house is furnished by the?
The electric meter for a new house is furnished by the power company. The box that holds the meter and anything past the box is the responsibility of the property owner.
What would cause circuit breaker to trip in new box from old box?
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
SMy Breaker box is tripping one of my 20A's How many times can I just reset it before I have to shut it down?
If you have contineous tripping on a breaker then there is a fault on the load of that breaker. Don't reset it any more. What is the breaker connected to?
Where is the electric load detector 98 Honda Prelude?
The electric load detector (ELD) is connected to the fuse box.
How do I connect a wall light switch that has 3 terminals the third being for the ground Which terminal should be connected to power coming from the breaker box?
How do I connect a wall light switch that has 3 terminals, the third being for the ground wire. Which terminal should be connected to power coming from the breaker box?
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
100 AMP breaker box what should the current read going into it.?
Depends entirely on the load. (ie What's connected to it)
