0
How can you disable the seat belt minder in your 2011 Kia Optima?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Is there a timing belt on 2011 Kia Optima?
The 2011 Kia Optima has a timing chain.
How do you disable the alarm for the seat belt on a 2011 Jeep compass?
wear the seat bealt
How do you disable the seat belt alarm for the 2008 mercury mariner?
You Can't. It is wired through the ignition system, Disable it car won't run. Safer to wear seatbelt. Wrong. All Ford products can have the Belt Minder disabled. Here is how you do it on the Mariner: Turn the ignition switch to on. Wait approximately 70 seconds for the seat belt light on the dash cluster to go out. For the seat belt you want to disable the minder on, insert and remove the belt approximately 10 times, you'll want to do it until you see the seat belt light turn on again. Then unbuckle the belt and the light will flash 4 times per second for a few seconds to confirm. This also works on F-150 pickups I know for sure, I just did it to confirm.
How do you disable the seat belt buzzer on a 2006 Ford Escape?
I just bougt the 2007 model and found a website that allows you to permanently or temp. disable the alarm. Hope this helps, because it was annoying the hell outta me, and as the site site, use at your own risk. You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete
What fuse controls the seatbelt alarm on a 2005 Ford Escape?
Instaed of messing with the fuse, you can temporarily or permanently disable the seat belt alarm. Below is s copied instruction from a website on how to do it. Just remember all is at your own risk. You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete
What Fuse disarms the seatbelt warning alarm on a 2007 Ford Tarus?
You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete.
How do you replace timing belt for 2003 Kia Optima v6?
how do you replace the timing belt and time the engine of a2003 kia optima
How can you disable your seat belt sensor chime for a 2003 Ford F-150 even though you wear your seatbelt?
Ford engineers have actually programmed a way to disable this "Belt Minder" feature. Here's a link to the owners manual: http://www.motorcraftservice.com/pubs/content/~WO3F12/~MUS~LEN/36/03f12og5e.pdf See page 108
Does a 2008 Kia optima 6 cylinder have a timing belt?
Yes , the 2.7 liter V6 engine in a 2008 Kia Optima has a timing BELT
How do you disable the seatbelt alarm in a 2002 Ford Crown Victoria?
Belt Minder Deactivating/Activating Preparation Before deactivating/activating the belt minder, set the parking brake. Place gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission). Place the ignition switch in the OFF position. Close all the vehicle doors. Unbuckle the driver's safety belt. Place the parklamps/headlamps switch in the OFF position. (If vehicle is equipped with Autolamps, this will not affect the procedure.) Deactivating/Activating Turn the ignition switch to the RUN position. (Do not start the engine.) Wait until the safety belt warning lamp turns off (approximately one to two minutes). NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be repeated. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This portion of the procedure can be done before or during belt minder warning activation. Turn the parklamps/headlamps on then off. Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for three seconds. Within seven seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled or disable belt minder is enabled. The following sequence of events confirm the belt minder is enabled: flashing of the safety belt warning belt lamp four times per second for three seconds three seconds with the safety belt lamp off flashing the safety belt lamp four times per second for three seconds again The safety belt lamp flashing four times per second for three seconds provides confirmation of belt minder disabled. After confirmation, the deactivation/activation procedure is complete.
When do you change a timing belt on a 2007 Kia Optima?
Does not have a belt but a timing chain in 2007.
How do you disable the seat belt alarm on a Chevy Colorado?
To disable the seat belt alarm on a Chevy Colorado, locate the alarm fuse. Pull out the fuse to disable the alarm.
