0
My husband and I just went thru this to no avail.... luckily my sister had the same hayward multi port valve and her sticker was still in tact. So on that note.... 12 o'clock is filter, 2 o'clock is waste, 4 o'clock is closed, 6 o'clock is bachwash, 8 o'clock is recirculate, and finbally 10 o'clock is rinse. we used fingernail polish to mark the positions, in case we forget again next spring.... Good luck
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How much earth goes into a Hayward Filter and when do you backwash it out and replace it?
5 lbs. Backwash with fresh d.e. once a month, be sure you bump the handle down once a week
Is there a diagram to take apart the outside door handle?
No, there is not a diagram to take apart the outside of a door handle. However, there is a diagram that shows how a door is held together, and from there a person can take apart the outside door handle.
Where can you find a door handle diagram for your Chevy C1500?
On google images type "door handle diagram Chevy C1500"
How can you get a diagram to replace the rear door hatch handle of a 2000 Dodge Caravan?
You can get a diagram for your 2000 Dodge Caravan rear door hatch handle and most Dodge dealerships. Your local library will have Dodge service manuals with the diagram.
How do we backwash sand filter?
Backwash a sand filter with a multiport valve; # turn off the pump motor # Start by Rrotating the handle on the multiport valve from the FILTER position to the BACKWASH position, Usually in the opposite direction) # Start the pump, Usually there is a clear bubble on the sand filter and you will see dirty water running through it, Wait until this water starts to run clear. otherwise keep an eye on the water exiting if you can until it runs clear. this can take about 2 to 4 minutes. # Shut off pump motor and move multiport valve handle to the RINSE position .Run on rinse for 15 - 30 seconds. once again you can keep an eye on the clear bubble to see the water clear if you have one. # Shut off pump motor again and move multiport valve handle back to the FILTER position # Now start pump again on and take note of the lower pressure. when the pressure gets too high again it is time to backwash once again.
How do you clean pool filters?
back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ---- Cleaning a Cartridge filter # Turn of the pump # Open the air bleeder opened, # Remove the cover, # Remove the cartridge # Hose it thoroughly from top to bottom, until all of the debris stuck to it is gone # Soaking the cartridge in a TSP (trisodium-phosphate) or similar solution can be helpful especially with older filters that can suffer from blocked pores. NOTE Do not use TSP with Baquacil or Soft Swim for sanitation.----
How do you handle the position given in an organization?
you do your work!
How can one assess if his pool has a clog in the filter line and how does he fix it?
Check the psi on the filter tank? If its lower than usual there is something stuck in the lines or jammed in the pump impeller. If its higher than normal, it just needs to be cleaned. Also, if you put the multiport handle into the recirculate position, this will bypass the filter. If everything works better in recirculate then you have a filter problem
Do you plug in a hose somewhere before setting to back wash an in ground pool?
Notnormally You may have to top up the water a bit because the back wash process tends to lower the water level of the pool a bit bit no hoses need to be plugged in anywhere as the backwash system is part of the filtration set up. Below I have put in backwash instructions---- back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ----
Can a pool sand filter handle being in the rain?
Yes
Illustrated diagram of a wood chisel?
The blade and the handle are the main parts of a chisel.
TravelPro Luggage Handle will not close Suggestions?
If a TravelPro Luggage handle will not close it is possible that the handle is in the locked position. Either use the combination lock to unlock the handle or insert the key to unlock the handle.
