Not just with a key. There is a Special key that has a bus button on it. They push it......TADAAAA!It opens!
with a key step1.take keys out of ignition step2. open backdoor emergency exit step3 lock emergency exit from the outside. Or just use the emergency button next to the door!! = they all have one.
Drivers door open Ignition off Switch ignition On then Off Close then Open drivers door twice Switch ignition On then Off Close then Open drivers door twice Close doors and lock using manual knob Switch ignition On then Off Twice Unlock using manual knob Passenger door lock and unlock I waited a few seconds for everything to settle, then everything worked.
yes, you need to close drivers door, open passenger door and use central locking button, then close passenger door and use key.
You can not close any door if the locking mechanism is stuck in the locked position. You must first get the mechanics to unlock.
1. Make sure all doors, hood and trunk are closed. 2. Open the trunk door. 3. Open the drivers door and sit in the drivers seat. 4. Close the drivers door. 5. Turn ignition switch to on and off 5 times ending in off.(do not start the car turn to just before starting) Your alarm light will turn on and the siren on the alarm will chirp to let you know it is ready. (this can also be used to test if you have the alarm) 6. Open the drivers door stay in the seat close the drivers door. 7. Press any button on the remote. The light will flash to indicate your remote has been programmed. 8. Repeat steps 6 & 7 to program any other remotes, up to 4 remotes a car. 9. To exit program mode open drivers door leave the door open. Close the trunk lid and close the drivers door the siren should chirp again and the red light will shut off. Test your remotes to make sure they work right.
;how to remove drivers door panel to repair door restrictor
please answer
if rear side door; unlock and pull handle. if boot lid; pull handle in drivers side door-well (side of the drivers seat) "door open"
use the passenger door.
1. Hold the key in your hand, drivers door is open all others closed and drivers door is unlocked. 2. Complete these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Complete these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Complete these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. In less then 4 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Complete these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door.
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door.
If your drivers side door won't open, try spraying some WD-40 into the area where the door connects with the lock inside the car. This will lubricate the lock.
# Start with the key out of the ignition. Open the driver door (all other doors are closed). Driver door is unlocked (other doors don't matter). # Perform these steps within 5 seconds ## Insert the key into the ignition (don't turn it) Pull key out ## Insert the key into the ignition (don't turn it) Pull key out # Perform these steps within 40 seconds ## Close, then open the drivers door. ## Close, then open the drivers door. ## Insert the key into the ignition (don't turn it) and pull it out. # Perform these steps within 40 seconds ## Close, then open the drivers door. ## Close, then open the drivers door. ## Insert the key into the ignition and leave in the ignition. ## Close the drivers doorTurn the ignition to ON (as far as you can go without cranking the engine), then back to off . ## Remove the key from the ignition. # Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. # Perform these steps within 40 seconds ## Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds ## Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted. # Open drivers door