0
How do i remove brown fuel line clip or connector from fuel pump or tank on a 03 ford expedition?
Bookee
You need fuel line clips that release the spring inside the clips.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do i Remove GM fuel injector electrical connectors?
There is a spring clip that holds them on. Squeeze the clip and then pull the electrical connector off.
How do you replace the passenger side mirror on a 2005 Ford Focus?
Removal and Installation Remove the trim panel. Release the clip. Release the locating tabs. Remove the trim panel. Disconnect the exterior mirror control switch electrical connector. Disconnect the exterior mirror electrical connector. Release the clip. Release the electrical connector. Disconnect the electrical connector. Remove the exterior mirror. Remove the bolt. If equipped, remove the screw. To install, reverse the removal procedure.
How do you change dipped head light bulb in a Ford Mondeo mk2?
pull head light clip down remove connector from bulb depress retaining clip extract bulb
How do you disconnect the electrical connectors on the fuel injectors?
use a small screwdriver to pry out the wire retaining clip located half way down on the plug. If equiped with a blue plastic clip in the connector: Pull or Pry the blue clip halfway out, using a small screwdriver or plyers. Push the tang on the side and completely remove the blue clip. Now with the blue clip removed squeeze the tang and pull the connector off.
How do you disconnect Verizon fios battery?
squeeze clear connector from top to bottom disengaging clip, and pull toward you. then remove battery from housing.
How do you get to the rear air fan motor in a 2004 for expedition?
You get to the rear air fan motor in a 2004 Ford Expedition by removing the bottom of the glove box. You will then see the motor housing, and a clip that you must remove to get to it.
Replace brake light switch in 2005 Chevy trailblazer?
At the base of the brake pedal you will see the brake light switch. When you find the switch you will notice that it is held onto the rod by retainer clip which can be quite difficult to remove without damaging the clip. Once you get the clip off you can undo the electrical connector and the switch should slide off. Then you can slide the new one on, connect the electrical connector, and re-install the retainer clip.
How do you change Volvo v70 front turn signal?
The connector has a metal clip on it. You need to depress the metal clip and remove the connector at the same time by wiggling the connector. You will need to use a screwdriver to depress the metal clip. It is tight in there so you may have to push a few wire protectors out of the way. Once you have the connector off you will need to rotate the bulb housing clockwise. I have only have replaced the passenger side so I can not say for sure about the drivers side housing rotation. I exerted a slight clockwise pressure on the protruding connector, with a screwdriver, and it rotates less than 1/4 turn. Remove the bulb and housing, change the bulb. Check bulb then assemble in reverse order. This can save you $20-$30.
How do you change sensor for low coolant level on 2001 Pontiac?
The coolant sensor is located approx. 1/2 way down the radiator on the passenger side of the vehicle. Disconnect the electrical connector, Remove the spring clip, pull out the sensor, replace with new sensor, replace the spring clip, connect electrical connector.
Honda odyssey directions for change head light bulb 2002?
changing a head light bulb in an odyssey is real easy. first remove connector from back of bulb. then remove rubber cover by pulling on one of the tabs. then remove retaining clip which holds bulb in place. remove old bulb, replace with new bulb, replace retaining clip, then replace rubber cover, and reconnect connector. all done. each light takes about 2- 5 minutes
How do you change the camshaft sensor on a 2006 pt cruiser?
remove the air filter box remove the steel clamp on rubber and steel hose atached to the engine and and take the two screws off the sensor, push the orange clip back on the electric connector unplug the connector replace the new sensor
How do you change headlights on a Pontiac Vibe?
Start on side without battery for visual ease, then feelon side with battery to find landmarks. Small hands are prferred for this job. Locate boot behind light bulb, remove carefully by tugging. Look carefully at wire clip behind connector; push in and down to remove from one side only, other side will stay attached. Connector with lightbulb attached will fall out. If it does not, carefully pull on boot of connector to remove connector/lightbulb assembly. Remove old lightbulb, check connector orientation to bulb, install connector on new light bulb. Carefully push new lightbulb/connector in place. The lightbulb fits in opening one way only. Carefully install wire clip. This will be critical to correct installation of boot. Install boot, being sure to seal around entire outside edge. from donna.henthorn@va.gov
