answersLogoWhite

0


Best Answer

The slave cylinder on a 1988 Ranger can not be repaired. The cylinder will have to be replaced, then the system bled.

User Avatar

Wiki User

โˆ™ 2014-08-26 19:40:18
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do i repair the slave cylinder on my 1988 Ford Ranger?
Write your answer...
Submit
Related questions

Where is the slave cylinder on a 1988 ranger four wheel drive with 2.9 liter engine?

The slave cylinder for a manual transmission hydraulic clutch is inside the manual transmission bellhousing


How do you replace the slave cylinder in a 1988 ford F150 6 cylinder fwd?

you just replace it


Clutch slave cylider location on a 1988 Pontiac Grand Am?

In a 1988 Pontiac Grand Am you will find the clutch slave cylinder located on the flywheel. You will need to remove the hush panel from the driver's side foot well to gain access to the clutch slave cylinder.


How to bleed the clutch master and slave cylinder on a 1988 Jeep Wrangler?

Purchase a repair manual at most parts stores, ( around $12 ) for detailed instructions on this and many other repairs.


How do you set the timing belt on a 1984 Ford Ranger 20L?

How do you set the timing on an 1988 ford ranger 4 cylinder


What size spark plugs for a 1983 Ford Ranger XLT 4 Cylinder?

i have a 1988 ford ranger xlt 4 cylinder and my spark size is 42-46 hope this will help


How do you change a clutch slave cylinder on a 1988 Chevy S10 Pickup?

You will need to remove the transmission to replace the clutch slave.


What engine is in a 1988 Ford Ranger?

The 2.0 liter 4 cylinder , the 2.3 liter 4 cylinder , or the 2.9 liter V6


Where is the clutch bleed valve on a 1988 ford f-150?

On the clutch slave cylinder


How does one tell if the clutch master cylinder is bad in a 1988 Nissan D21?

Look for leaking fluid at the slave or master cylinder.


V6 2.9L Ford Ranger 1988?

Yes , there was a 2.9 litre V6 engine available in a 1988 Ford Ranger , as well as the 2.0 and 2.3 litre four cylinder engines


Where do you put the clutch fluid in for a 1988 ford ranger What does the reservoir look like?

Should be on firewall next to master cylinder


What do you have to do to remove a starter for a 1988 Chevy Cheyenne 6-cylinder standard trans?

you must remove the clutch slave cylinder and line. Then unbolt the starser and install the new one


What is the stock cylinder compression on a 1988 V6 2.9L ford ranger?

Highest and lowest cylinders should not exceed a 10% difference


How do you change the ignition key cylinder on a 1988 Dodge Caravan Is there a detailed diagram to do it?

Yes, buy the Haynes Repair Manual.


1988 Honda Accord brake pedal too low?

Its becaue the slave cylinder is has a leak, and pressure is lost when you press on the brakes.


Diagram of a fuse box for a 1988 Ford Ranger?

diagram of fusebox on 1988 ford ranger


Water pump for a 1988 Ford Ranger at?

i need help with the temp.gage in a 1988 ford ranger


Will a Ford 300ci straight six fit into a 1988 Ford Ranger?

www. the ranger station . com ( no spaces ) lists engine swaps for 4 cylinder , V6 , and even a 5.0 L V8 but not the straight 6 cylinder engine , so I'm pretty sure it is too long


Does a 1990 rm 125 cylinder fit a 1988 rm 125?

No, the 1990 RM cylinder doesn't fit the 1988 cylinder. The 1988 cylinder is the only year that'll fit on a 1988 motor. This was the first year Suzuki did that. It actually sucks because I have a 1988 RM 125 I've been trying to get a cylinder for. And the 1988 cylinder is the only match. Nothing else would fit.


Where is the fuel pump on a 1988 Ford Ranger 4-cylinder?

If fuel injected - in the fuel tank If not in the front lower section of engine - follow fuel line


When was Rocket Ranger created?

Rocket Ranger was created in 1988.


When did Rocket Ranger happen?

Rocket Ranger happened in 1988.


How do you replace a broken throttle cable on a 1988 Ford Ranger?

how do i replace a throttle cable on a 1988 ford ranger pickup


How do i put an aftermarket air intake on this piece of crap 1988 ford ranger?

If it's a piece of crap , why do you want to spend money on changes that aren't a necessary repair ?