How do i stop seat belt warning bell in a dodge Dakota?
Buckle the seat belt.
It is inside either the body computer or cluster and can not be removed.
The serpentine belt on a 2003 Dodge Dakota is replaced by loosening the belt tensioner and slipping the belt off. It can then be removed from the engine accessories and a new belt installed.
belt diagram 1992 dodge Dakota with 318
All 1998 Dodge Dakota's have a timing chain and not a belt.
88.50 in belt
It typically costs between $100 and $150 to replace the serpentine belt on a Dodge Dakota. The belt costs around $30 with the rest being labor.
You can get a belt diagram for your 1991 Dodge Dakota 3.9 liter engine, at most Dodge dealerships. Most auto-parts stores will give you a belt diagram when you purchase a new belt.
Done automatically by belt tensioner
For the 1990 Dodge Dakota : The 2.5 litre four cylinder engine has a timing BELT The 3.9 litre V6 and the 5.2 litre V8 engines have a timing CHAIN
by putting on your seatbelt
The Dodge 3.9L has a timing chain.
Its 15mm on my '97
No, it has a timing chain. No, it has a timing chain.
It could. It could.
The 1997 Dodge Dakota came equipped in three engine options. For the 5.2L the accessory drive belt (with air conditioning) is Goodyear #4070972.
It has a timing chain
Ask your dealer
What size serpentine belt do you need on a 2000 dodge Dakota 4.7l when bypassing the air conditioning unit?
Ask for one for a 2000 Dodge Dakota 4.7 L that was not equipped with A/C from the factory.
Just connect you seat belt and the bell will go off. If it is staying on even after you connect the seat belt take it back to your Honda dealer for repair, as it is still under warranty.
There should be a diagram on the underside of the hood or on the radiator.
Take pressure off belt tensioner and belt should slide off pulleys
Can you put a belt for a non air conditioner equipped 4.7L Dodge Dakota on an air conditioner equipped 4.7L Dodge Dakota to eliminate the air conditioner compressor?
Yes, you can, and the routing will remain unchanged except for the omission of the air conditioner pulley. If the belt turns out to be too long or short, simply obtain a belt of slightly longer or shorter length, as appropriate.
Raise up on the tensioner to remove the belt. there shouold be a routing schematic on the fan shroud. If not draw one before removing the old belt.
Change at 105,000 miles. Warning: (Interference engine, if the belt breaks serious engine damage will occur)
It transfers the crankshaft rotation to the alternator, water pump, ac compressor, and power steering pump.
Not sure exactly what is meant by the question, but no, the fan belt should not affect the radiator. Although, if the belt is broken or too loose, you may experience some engine overheating issues.
You remove the compressor and replace the belt with one for a truck with out ac
1995 dodge Dakota sport will not start We have replaced the fuel pumpfilter It will crank but not fire?
check timing chain/belt to see if it is broken
If you are referring to the tensioner pulley's nut size, it is usually a metric 15mm nut.
You don't. The pulley is pretensioned by the manufacturer. If the belt tension is incorrect, the pulley must be replaced.
1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled… Read More
98 dodge Dakota squeaking under hood when foots on gas take foot off it stops don't know if its belt or pulley just checking before you buy?
Sounds like a belt is slipping.
should be on the hood look up after you open it or by the radiator on the area were your emmisions placard is installed
You don't. If it has stretched too much for the tensioner pulley to handle, you need a new belt. Or, if the tensioner pulley is not applying correct tension, the tensioner pulley must be replaced.
you must remove belt and a/c comp. if you have it. $5 part 2 hour job.
The ignition coil is on the front passenger side of the engine, next to the belt tensioner.
i am about to try from what i hear u can use a shorter belt will report back worked fine duralast 900k7 24.99 at autozone
the timing belt is not the same as the serpentine belt.the serpentine belt goes around your water pump pulley and the power steering pump,air condition compressor pulley and the alternator pulley.the timing belt goes around the camshaft and the crankshaft.it is not visable without taking the timing belt cover off.
This does not have a multiple belt system like the older cars. This has a serpentine belt. 1 belt to drive all vehicle accessories. The auto tensioner is located on the right side of the engine (pass side) take a 15mm socket or wrench and put it on the only pulley it fits on. note the belt routing, remove belt. reverse to reinstall new belt.
Open hood, look on the frame in front of the radiator or on the hood itself. Should be a diagram w/ air conditioning and w/out.
Plug The Seat belt in.
The timing belt warning light, on a Toyota Innova, can be reset by removing the timing belt warning light fuse. Leaves the fuse out for 10 seconds and put it back in.
A high-pitched whine in a Dodge Dakota only when the weather is cold might be a normal thing. When the weather gets cold, the belts, starter and alternator need time to warm up. Try a little drop of dish soap on the fan belt to see if this helps quiet the whining.
The Dodge Caliber has a timing chain, not a timing belt.
the warning lights comes on indicating that the timing belt needs to be changed. even once the timing belt is changed, the warning light will stay on until is it reset.
You don't. It employs a spring loaded automatic belt tensioner pulley located usually on the passenger side of the engine. If your serpentine belt is too loose, either the tensioner pulley has failed (possible, but unlikely) or the belt has stretched beyond the limits of the tensioner pulley and needs to be replaced (more likely).
well is it a 4 cyl, v-6 or v-8? there should be a diagram on the underside of the hood or when you open the hood look down where the hood latch is.
TAKE TIRE TOOL AND PRY TENTIONER UPWARDS TAKE SERPENTENE BELT OFF REMOVE TENTIONER PULLY PUT NEW ONE ON PUT NEW BELT ON SPEC SHOULD BE ON THE HOOD OR THE NEAR THE RAIDIATOR PRY PULLY BACK UP SET BELT