0
How do you Remove the serpentine belt on 97 suburban with a bolt in the center of tensioner?
Wiki User
∙ 16y ago
There should be a square 1/2 hole off center of the tensioner use a 1/2 breaker bar in this hole to take tension off belt
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you change the serpentine belt tensioner on 2.4 liter 1998 Malibu?
remove the belt. then in center of the tensioner is a bolt that goes into engine. remove this bolt. then tensioner should come off.
How do you replace belt tensioner 06 G6?
Begin by removing the serpentine belt from your Oldsmobile Cutlass. Remove the tensioner pulley retaining bolt. The retaining bolt will be in the center of the pulley. Reverse the process to install your new belt tensioner.
How do you replace the belt tensioner on an 1989 Chevrolet celebrity?
There is a center bolt in the fixed end of the belt tensioner. To replace the tensioner: 1. Using a 3/8" breaker bar release the belt tension and move the serpentine belt out of the way. 2. Use the appropriate wrench to take out the one bolt, then remove the tensioner. 3. Install the replacement tensioner and tighten the bolt. 4. Put the serpentine belt back on.
How do you replace Serpentine belt 95 pathfinder?
Take a 14 mm wrench and put on the center bold of the tensioner. Then pull back releasing pressure on the belt. Remove and replace. Take a 14 mm wrench and put on the center bold of the tensioner. Then pull back releasing pressure on the belt. Remove and replace.
How do you remove the serp belt on 1997 suburban?
locate belt tensioner below alternator on pass. side insert 3/8 drive ratchet in center of tensioner pulley rotate to loosen belt remover belt
How do you replace the balancer on a 1988 celebrity?
Replacement of the harmonic balancer is most conveniently done with the engine out of the car. 1. Release the belt tensioner and remove the serpentine belt. Take note of its routing. 2. Remove the bolt from the center of the balancer. 3. Use an appropriate puller to remove the balancer from the crankshaft. 4, Use the center bolt to pull the replacement balancer onto the crankshaft. Replace the serpentine belt.
Where is serpentine belt tensioner located on a 1991 Chrysler new yorker salon?
It is the smaller pulley in the center rear of the belt.
How do you change the belt tensioner pulley on a 1994 Chevy Silverado?
Remove the belt, then remove the bolt in the center of the spring tensioner with a 15mm wrench, install new one
How do you replace the serpentine belt on a 1999 jeep Cherokee Sport?
Loosen the tensioner (It's the only pulley out of 7 that is not attached to a unit) by using a 15MM wrench, then loosen the tensioner screw on the upper left of the tensioner bracket (15MM as well), until you can remove the old belt, replace w/new belt and tighten screw then center tensioner bolt. Be careful of ADVANCE AUTO PARTS.....They like to give you the wrong belt. A good belt to use is the DRIVE RITE serpentine belt (Part No. 950K6), assuming you have a 4.0Ltr engine. Hope this helps!
Where is the tension bolt for the serpentine belt on a Chevy Malibu?
there is no tension bolt ! if the belt is loose it is either a stretched belt or the tensioner is bad. the only bolt on a tensioner is the bolt that goes through center of tensioner to hold it to the engine. no adjustment. good-day ! on the tensioner there are a few marks to tell you if it needs replaced, it should be on the center mark if all is ok. if its on any other mark. replace belt or tensioner if needed. the marks are on the front side of tensioner accross from the center bolt. alt, water pump, etc, are all stationary.
How do you loosen the serpentine belt on a 1999 Chevy Malibu in order to replace the alternator?
there should be a tensioner pully. Put the 3/8 ratchet in the center of it and turn.
How do you release the belt tensioner on a 2002 2.4 l toyota camry to repace the serpentine belt?
The 2002 Toyota Camry belt tensioner pulley can be loosened by loosening the pulley nut. The pulley nut is located in the center of the pulley.
