answersLogoWhite

0


Best Answer
Copy

rech behind the bumper and turn the bulb socket and pull it out !!!!

User Avatar

Wiki User

โˆ™ 2015-07-15 20:04:30
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you access the license plate lights on the rear bumper of a 1998 GMC Jimmy to change them?
Write your answer...
Submit

Related Questions

How do you change the lights over the license plate of a 1991 Chevy Camaro?

You can remove the panel inside the back of the car. From there you can access your tail lights and your tag lights.


How do you change the horn on a 2001 Ford Escape?

you need to remove the bumper cover to access the horn. The horns at below to the out side of the head lights


How do you change the front lights on a peugeot 106?

you haft to remove the bumper first to get to the bolts holding in the lights


Would a 1998-01 Acura Integra front bumper fit on a 1997 Acura Integra?

Yes you just need to change the headlights and bumper lights along with the bumper


How do you remove and replace the head lamp assembly in a 1992 Honda Accord?

first remove the bumper turn lights...two screws on one each light..then remove the lights carefully, so you do not break them.... After that...remove the bumper screws in the wheel wells.... Then, where you have removed the bumper lights...with a socket extension..and a 12 mm socket...remove two bolts on each bumper mounts.....then the bumper should come off in a forward direction.... you now have access to both headlight assemblys.


How do you change the license plate lights on a Chevy Tahoe?

On my 98 Tahoe under the bumper behind the are where the tag is located you just pull the light assembly out. It has a little pressure clip. replace light and replace assembly the same way.


How do you change front park lamps on a 98 cavalier?

There are 3 screws located under the front bumper under the light you need to replace take these 3 screws out and you have full access to all the lights in front. do this for each side.


How do you change a license plate bulb on a 1991 Chevy cavalier z-24?

their are 4 plastic nuts in the trunk that loosen the light assembly that the lights are in. Remove those and pull the assembly out and twist the connector for the license plate light to access the bulb.


How do you replace the license plate bulb on a 1999 Dodge Intrepid?

if it is the same as a 2001 one then just unscrew the light cover(there should be two screws on the cover) and you should be able to access the bulb. If the wiring falls inside the bumper just put your hand under the bumper and push it back out. CAUTION: turn off your lights when changing the bulbs as it will be hot if left on.


Are lights covered by a bumper to bumper warranty?

At the Chevrolet dealership I work at yes the bumper to bumper covers everything so I think all should cover them


How do you replace 2001 aurora rear bumper lights?

The rear fog lights are accessable from under the car. You have to reach up and under the rear bumper.


How do you change side marker lights on 2002 Lexus is 300?

To change the side marker lights on this model, remove the screws of under cover that attaches to the bumper. It would be easiest to do if the vehicle was lifted up in some way.


How can you install after market fog lights for Toyota 4Runner under front bumper?

If the aftermarket lights are not a factory option then the lights will need to be drilled into the bumper. Afterwards the lights will also need to be properly spliced into the existed wire harness.


How do you change the tail lights in a 1984 corvette?

The tail lamps are serviced from underneath the vehicle, between the frame extension and rear bumper.


Where is the horn on a 89 prelude?

there are two duel tone horns there is one on each side kind of behind the bumper you can access them bye removing the splash guards and they are all the way to each side of the bumper near were fog lights would be


Will a front bumper from a 01-02 cougar fit a 2000 cougar?

Yes, but there will a much bigger gap between the bumper and the headlights than there was with the stock bumper. Additionally, when equipped with fog lights, the 01-02 bumper had different fog lights, so your new bumper may not come the new ones, meaning you'll have to either find a pair, or live with two great big holes in your bumper, that is of course assuming that the new bumper had fog lights.


How do you change the reverse lights in a 2003 GMC Envoy?

You must pull off the plastic panel from the inside of the truck to access the lights.


How do you change a xenon bulb in a Renault laguna?

Renault suggest you remove the front bumper to access the bolts that hold the headlight in place then you can easily change the bulb ! It can be done if you remove the few parts that obstruct access to the bulb. Don't forget that the HID uses 30,000 volts to light up the Xenon bulbs so make sure the lights and ignition are off!


How do you change the bumper lights on a 1998 jetta?

well, it all depends on what bumper lights you're trying to change. say for example the side markers, you just pop them out, unplug, plug in new ones and pop them back in. the front left/right signals, the same way. pop out, unplug, plug in new ones, pop back in. fog lights are a different story. you got some wiring to do.


How do you wire license plate lights on a gas scooter?

to wire the license plate lights you must have lights and wire them to the scooter.


How do you turn off the light around the license plate on a 2002 Oldsmobile Bravada?

There should be a connector for the lights above the rear bumper, but you may not want to disconnect it because then your likely to get pulled over for having a faulty license plate light


How do you replace fog lights mounted in bumper 1996 jeep grande Cherokee?

I've never seen fog lights mounted OEM "in" the bumper on a 1996. However if your talking about on top of the bumper then that is easy. Just unbolt them than take them apart and replace the bulbs. Or do what I did and install newer aftermarket ones, they work much better. With the aftermarket lights you may have to modify the OEM brackets a bit. I used rubber spacers to help hold the new lights in place and cut down the vibration. If your lights are mounted in the bumper, you will have to remove the bumper.


How do you remove a 89 civic bumper?

its a series of screws and bolts.. its really easy.. first the two screws on each side of the wheel well where it meets with the fenders on each side of the car.. second take the bumper lights out with the single screw either on the inside or outside (i forget).. pull out the the bumper lights and take out the lights from the light sockets on the bumper lights.. third behind the bumper lights is where the bumper support bolts on to the frame.. its alot easier if you take of the bumper support with it.. they're two 12mm bolts one on top the otherbehind each bumper light.. take off all four.. then the bumper will hang loose.. on the bottom of the bumper will be two 10mm bolts where the bumper connects to the radiator support.. take those off as well.. and voualla.. (how ever u spell it) the bumper is off when replacing any front end piece (besides the hood) it is always good to take off the front bumper.. i found out the hard way when i tried to replace my filler panel (between bumper and head light)


How do you remove civic type r tail lights?

you have to remove the bumper in order to remove the lights :)


How do you change the license plate lights on a Saturn Ion?

With a 22 calibur rifle and a guy north of I-10.