How do you bleed the clutch on a 1993 Mazda B2200?

Automatic:yes. Manual:no.

i have a 1993 Mazda b2200 and the fuses are left of the steering colomn. the cover pulls down and the radio fuse is on the top to the far left.

The Mazda B2200 truck body did not change much, if at all between 1986 and 1993. There should be no differences in the shape of the engine compartment. -Kyrasis6 Owner of Mazdatruckin.com

1993 Infiniti G20 does not have a hydrolic clutch! It has a cable, that runs under the intake stuff.

stock horsepower and torque was 85 HP and 115 LBS of torque

i have a b2200 Mazda 1993 and everytime i brake a clicking noise come out of the passenger side like in the back of the seat at the same time the brake pedal moves down with each click what can that be.

it will fit the b2200, b2000,b2600. I think 1987 to 1993.

All the 1986-1993 mazda b series trucks were manufactured in japan.By the way great built trucks for that matter.

Pump the pedal to the floor and then screw on the cylinder.

Mazda did make a 1993 b2300(it was a b2200 or b2600).However the answer is follow the upper radiator hose to the block near the valve cover.The upper radiator hose connects to the thermostat housing.Easy.

All 1986-1993 models have the same doors.

YOu need to blead the system .. then it should require no adjusting

Pictorial guide: http://www.miata.net/garage/clutch2.html

Right above the slave cylinder there is a bleeder screw. Just unsrew it and have someone hold in the clutch to start the bleed.

Is very possible but it is a wate of time and money, I have B2200 and trust me the smallest engine that can manage the weight of that mini pick up is a 2.0L anything smaller is a waste, I tried with RX7 engine and it is not that reliable, unless is turbo and have to play with diferential ratios

NO!! The Mazda engine and ford engine are totally different period.Mazda was still strickly Mazda until 1993. It was not until 1994 when Mazda and ford became the same on engine and tranmission similarities.You need a Mazda engine for your Mazda transmission.Note the 1986-1993 Mazda bseries trucks are all Mazda manufactured.Ford is not interchangeable with these models period.

On a 1993 Mazda Protege, neutral safety switch (also called the shift interlock switch) is located at the top of the brake pedal. It is situated between the headlight relay and the clutch switch.

Go read the instructions, unless you're too MAN enough to do it.

how to i change a clutch in a 1993 ford ranger

have someone pump clutch pedal about 3 times and hold to floor,then go to your clutch slave cylinder,its bolted on the side of transmission,with rubber cover,and open bleeder valve ,u might wanna get aclear hose that fits the bleeder valve and put other end in glass container so u can see air coming out,then bleed your clutch damper ,which is located on left side firewall.

I have a 95 b2600 and I had a hard time trying to find the horn, but mine was located just behind the right headlight I think tucked away behind body supports and was bloody hard to get out

Where is the clutch fluid on 1993 nissan pickup truck.

I can tell you at least for the usa version Mazda bseries trucks the 1993 did not have day time running lights!Unless you have a foreign version or Canada version daytime running lights were not offered period for any of 1986-1993 Mazda trucks American sold trucks.If you asked your question incorrectly just reply back on this post under the discussion tab for this post to correct instead of asking the same thing again please.

Some cars have no valve and you have to loosten the line to bleed the cyl. Fill the slave cyl as full as you can get it before mounting it .

On the drivers side of the transmission bellhousing Check out : www . the ranger station . com ( no spaces ) Click on Tech Library Under the manual transmission section they have a good write-up on how to bleed a hydraulic clutch