Contact the manufacturer for data on your unit . You can perform an enthalpy calculation as well .
You will need to give more information. The Btu's of baseboard is determined by the water temperature and the type and size of the element. Copper fin tube (copper pipe with aluminum fins over it) heats up quick and loses heat quickly it also has many diameters of element (copper tube). Most common in residential is 1/2", 3/4" & 1" ID (the OD will be 1/8" or so larger). There is also Cast iron baseboard that heats up slowly and cools off slowly (this is a much more even and comfortable heat). You should never mix and match cast iron radiation and copper radiation of the same circuit it will cause large temperature swings in conditioned area. Tell us what the boiler temperature is set to and what the type of radiation is and you'll get an answer.
There are no BTUs in an office water-cooler. But you can calculate how many BTUs are removed by the cooler. One BTU or British Thermal Unit is the amount of heat energy required to raise the temperature of one pound of water one degree Fahrenheit. There for when you remove one BTU you are lowering one pound of water one degree Fahrenheit. So if you know how many pounds of water you have and the temperature of the water you start with and the temperature of the water comming out of the cooler you can calculate how many BTUs the cooling unit of the water cooler has removed. BTU=Temp1 - Temp 2 X LB water
First, things are not made of cement- they are made of concrete- which consists of cement, sand, gravel and water. Mix them using 1 part cement, 1.5 parts sand, 3 parts gravel. To calculate how much CONCRETE you need, multiply depth X width X length in inches, then divide by 1728. This will tell you the number of cubic FEET of concrete. To get the number of cubic YARDS, divide the cubic feet by 27. If you are using packaged concrete mix (Sakrete is one) then an 80 lb bag makes 0.6 cubic feet of concrete. NOTE: If you are working with concrete for the first time- do not add too much water (weakens the concrete) and do not get wet concrete on bare skin- it will cause a chemical burn. Wash it off promptly if you do.
The objective of a water supply it to get water into houses. The function of the pipe it to carry that water and the function of a tap is to control the flow of the water.
liquid,salt water 97 % frozen 2 % liquid,fresh water 1 % APEX:)
Baseboard heaters are an excellent way to heat your home. There are two main types, water radiator and electric radiator. Both types draw in cool air from the floor, heat it, and then force it up the walls. This creates circulation in the room and allows an even heat. They can be purchased from local home centers like Lowe's or Home Depot.
Yes. You might want to check to see what recommended temperature is for water entering the baseboard units and insure the water heater will meet that. Something else to consider is that there will need to be a pump in the water circuit to circulate the water. A tank type water heater would also work to store hot water until needed by the baseboard units in an instance where heat might be generated at a time not needed by the baseboard units.
Yes, 1/2 inch supply to fill boiler will work fine. Piping going to baseboard heaters needs to be sized properly. 1/2 inch piping to baseboard heaters not recommended. Most hot water baseboard heaters piped with 3/4 pipe.
You would add it to the boiler
sometimes
About 150 deg.
there is supposed to be water in the radiator. your radiator is supposed to be evenly mix 50/50 with radiator fluid and water, preferably distilled water.
how to calculate profit maximizing water level under quadratic cost function
Most output ranging from 560 to 600 btuh per foot, this is with 170 F water temps. I have no way to know your specifics from where I am.
There is a water reservoir tank that goes to the radiator that you can add the water to.
120-160 Degrees Fahrenheit
A bleeder valve to remove air in the system