0
To change the hazard switch on a Proton Persona, you typically need to remove the trim piece surrounding the switch and then locate the mounting screws that hold the switch in place. Once the screws are removed, disconnect the wiring harness and replace the switch with a new one. Be sure to test the new switch before reassembling the trim piece.
What else can I help you with?
Changeing switch on a craftman tablesaw with a household switch-?
It is not recommended to change the switch on a Craftsman table saw with a household switch. The original switch is designed specifically for the saw's voltage and amperage requirements, ensuring safe operation. Using a household switch may not provide the necessary protection and could potentially cause damage to the saw or pose a safety hazard. It is best to consult the manufacturer or a professional electrician for appropriate replacement options.
Why would your 1999 proton persona 1.6XLi suddenly lose ignition lights Engine died and will not start but will turn over and all other electrics work also immobilizer light goes out?
This issue could be caused by a few possibilities, such as a faulty ignition switch, a problem with the immobilizer system, or a failing fuel pump. It's recommended to have the car checked by a qualified mechanic who can diagnose the exact cause of the problem and perform necessary repairs.
Can you operate a hunter fan with a dimmer switch?
No, it is not recommended to operate a Hunter fan with a dimmer switch. Fans require a specific type of control, such as a fan speed switch or a remote control. Using a dimmer switch can damage the fan's motor and may cause a fire hazard.
Can you change a light switch to toggle switch outlet?
You can if you have a neutral wire present. If the existing switch is what is called a "switch loop" then you can not change the existing switch to a switched outlet. You can identify a switch loop by looking at the wires coming into the switch bow. If there are only one set of wires usually a black and white and they go directly to the switch then you have a switch loop
Can you use this switch for three phase incoming and single phase outgoing?
No A intermediate switch can not be used to change three phase to single phase.
How do you change the hazard light switch in a Saturn L200?
Hit the Hazard button it will be a triangled shaped button
How to change Saturn L300 turn signal flasher?
the signal flasher is the hazard light switch......remove the radio bezel and change the switch
How do you change the indicator relay in an Audi TT?
The turn indicator relay in an Audi TT is integrated with the hazard switch. To replace the relay you would need to replace the hazard switch.
How to change the emergency light switch on a Mazda mpv?
Are you asking how to change the Hazard switch? What makes you think it is bad? They almost never go bad and I would be really surprised if it were. Have you replaced the Flasher Relay for the hazard lights.
How do you change out the hazard switch in 2000 Malibu?
remove the trim around switch, remove screws that hold switch in, pull switch out, remove wire connector.
Skoda octavia 2001 1.8t indicators do not work?
change the hazard switch first
Why aremy side lights not working on 1998 vw passat?
change your hazard/flasher switch pretty much just your hazard button
How do you put in a hazard switch?
how do you put in a hazard switch in 1997 chevey malubu
How do you replace hazard switch 2001 Oldsmobile alero?
How do you replace the hazard switch
How do you turn on the hazard lights on a 1996 Monte Carlo?
simply depress the hazard light switch on top of the steering column. if the switch does not turn on hazard lights the switch may need to be replaced. this is common with this body platform. Be aware that the turn signal and hazard switch are all one part. it is not a difficult task to change, but remember that you will need some expertise for dealing with the air bags and steering wheel removal
Diagram for 2002 Honda Accord hazard light switch?
hazard switch dont lights on
Hazard signals not working and turn signals not flashing in '99-00 Volvo S70's. How to fix?
The turn signals operate through the Hazard switch. The Hazard switch assembly is in the radio console inside the car and must be replaced. This unit is about $90 CDN and can be purchased from the dealership. I replaced mine by pulling out (Carefully!) the radio console (the owners manual will show you how to do this). After that, you: Push the old Hazard Switch out from the rear of the radio console. Unplug the wire at the end of the broken Hazard switch. Plug the wire into the new Hazard switch. Push the Hazard switch back into the radio console and slide the radio console back in place. It takes 2 minutes if you get someone to hold the radio unit while you change the switch. Good luck!
