Spark Plugs and Wires
Geo Storm

How do you change a spark plug on a Geo Storm?

383940

Top Answer
User Avatar
Wiki User
2008-11-15 05:17:37
2008-11-15 05:17:37

There's one spark plug mounted on the exhaust manifold. You have to remove it, usually with a hammer and screwdriver. The just thread a new one in.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

#1 is about 2 to 3 O'clock firing counter clockwise 1342.

User Avatar

The 1995 Geo Metro spark plug torque specification is 20 pounds. You should torque the spark plug intent pound intervals.

User Avatar

If you have no spark, you would likely have a problem with the magnito (ignition).

User Avatar

My 92 model Geo spark Plug gap is 0.39 thousands of an inch. One Liter 3cyl/5sp. Plug is a ngk BPR6ES-11 Hope this helps

User Avatar

The spark plug gap for a 1995 Geo Prism Isi 1.6 liter should be set at .032 inches. A spark plug for this vehicle will be preset at the factory and should not need further adjusting.

User Avatar

place a screwdriver inside the spark plug boot and close to, but not touching, a ground. have someone crank the vehicle as u look for the spark. Best to do it at nighttime when its dark...its also a good way to find plug leaks. they also sell an inexpensive tester at the parts store that will do this also

User Avatar

0.028 geo tracker 1990, 8 valves 2 doors

User Avatar

Check the ignition circuit in the Storm. Start by checking the crank position sensor, then the coil pack to find the lack of spark.

User Avatar

.41 is the gap specified by the Haynes manual for the 1990 Geo Prizm.

User Avatar

Factory manual says 0.031, not 0.042.

User Avatar

AnswerThey are inside the valve cover. Looking from the front of the car you will see the spark plug wires routing from the distributor cap to each plug. To change the plugs remove the spark plug wire and use a spark plug socket attached to an extension. I recommend adding some duct tape to the socket/extension connection to prevent the socket from coming off in the valve cover.

User Avatar

have you tried to change the spark plugs? or the wires? it cost me only 16 usd to buy new spark plugs cables on the store, just take the Vin number of your car and they might help you find the right ones

User Avatar

ANSWER: 0.039 to 0.045 inch (1.0 to 1.1 mm)

User Avatar

plug the wire in on the driver side of the car and 4 bults in it

User Avatar

According to the Haynes Manual- 0.031 inch gap

User Avatar

Plugs are in the top of engine I think that's obvious well anyway pull and twist a little on the boots carefully by the boot not the wire, you will need I believe a 7/8 spark plug wrench. if you don't have a spark plug wrench(with rubber boot built inside the socket) you will have a problem getting the spark plugs out,that is once they are unthreaded.

User Avatar

1-3-4-2 Distributor rotates counterclockwise.

User Avatar

Remove the fuel tank then the gauge and pump.

User Avatar

look at sticker under hood. i believe it is .39 i have a 4 cyl 1996

User Avatar

Repair kit availale at most auto parts stores

User Avatar

Any Auto Parts store can tell you exactly what to install. Or you can simply remove an old plug and purchase the exact same plug.

User Avatar

it can be done but you will have to change all of ur wirring harness from the prism because the prism is basically a Toyota and a storm is a izuzu impulse knockoff


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.