Auto Parts and Repairs
Air Conditioning and Coolant
Mercury Sable
Heating Ventilating and Air Conditioning

How do you change an air conditioner hose on a 1996 Mercury Sable GS?

464748

Top Answer
User Avatar
Wiki User
2015-07-15 18:33:16
2015-07-15 18:33:16

Hey Jennifer==Simply take the hose off and replace it. Then evacuate the system and add refrigerant. GoodluckJoe

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

the air conditioner and heater are two separate things.(not connected) ;) it may have a fuse. or the it could just be bad.

User Avatar

( fuse # 21 ) is a 20 amp fuse for the cigarette lighter on a 1996 Mercury Sable

User Avatar

The most common cause for a 1996 Mercury Sable not starting is a dead battery. The second most common cause for the automobile not to start is a lack of fuel.

User Avatar

The 1996 Mercury Sable the OBD 2 connector is under drivers dash next to kick panel

User Avatar

On a Mercury Sable : firewall 1-----2-----3 4-----5-----6 front of vehicle > driver

User Avatar

On a 1996 Mercury Sable : The thread on cap on the engine coolant reservoir is the pressure cap / radiator cap

User Avatar

No, a Generation 2 (1992-1995) Taurus/Sable Windshield will NOT fit a Generation 3 (1996-1999) Ford Taurus/Sable.

User Avatar

On a 1996 Mercury Sable : The fuel pump shut off switch ( inertia switch ) is in the trunk , behind the trunk liner on the passenger side ( there is an access hole )

User Avatar

According to the 1996 Mercury Sable owners manual :It came from the factory with a 50 / 50 mix of distilled water and GREENcolor antifreeze ( meeting Ford specification ESE-M97B44-A )

User Avatar

The 3.0 liter " Duratec " V6 engine used in the 1996 Mercury Sable has ( 1 timing CHAIN to each cylinder head , so there are 2 timing CHAINS )

User Avatar

An oil leak on a 1996 Mercury Sable may be caused by a hole in the filter or oil pan. These parts can be replaced at any auto parts store. A mechanic will be able to pinpoint the exact location of any leak.

User Avatar

To replace the 1996 V6 Mercury Sable climate control and take out the old control, you will need to remove the covering below the steering wheel and dashboard. Then, access the climate control in the instrument panel and remove the old control.

User Avatar

According to the 1996 Mercury Sable Owner Guide : With engine oil filter change : The 3.0 litre " Vulcan " V6 engine takes ( 4.25 litres of 5W-30 engine oil ) The 3.0 litre " Duratec " V6 engine takes ( 5.2 litres of 5W-30 engine oil )

User Avatar

A 1996 Mercury Sable has either : One timing CHAIN on the 3.0 litre " Vulcan " V6 engine or Two timing CHAINS on the 3.0 litre " Duratec " V6 engine ( one CHAIN to each cylinder head )

User Avatar

On a 1996 Mercury Sable : The automatic transaxle ( transmission ) fluid level dipstick is near the firewall and the brake fluid reservoir ( looking from the FRONT of the vehicle it is to the left of the reservoir )

User Avatar

Around 3,400 lbs for a sedan and 3,550 for a wagon circa 1996-2006.

User Avatar

( 5W-30 ) is the preferred oil , according to the Owner Guide

User Avatar

Go outside, look under the car, and count them.

User Avatar

It is located where the upper radiator hose connects to the engine.

User Avatar

On a 1996 Mercury Sable : There were two engines from the factory : The 3.0 litre " Vulcan " V6 engine , which is an Over Head Valve / pushrod design engine or the 3.0 litre " Duratec " V6 engine , which is a Dual Over Head Cam ( DOHC ) design

User Avatar

5W-30 is the preferred engine oil , according to the Owner Guide

User Avatar

According to page 112 of the Owners Manual, fuse #6 covers the reverse/backup lights.See "Related Questions" below for more


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.