Ford F-150

How do you change an ignition switch on a 1986 ford F150?

91011

Top Answer
User Avatar
Wiki User
2009-03-21 22:03:31
2009-03-21 22:03:31

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTEOn column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.

The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

There are images available online to help you see where the Fuel reset switch on a 1986 Ford F150 is.

User Avatar

How to drill out ignition switch on 1985 ford f150?

User Avatar

A 1986 Ford F150 starter won't stuff off when the key is turned off if the ignition switch is jammed. This will cause the start signal to be sent to the starter continuously.

User Avatar

I just purchase a f150 that needs a new ignition switch and the man at auto zone gave me directions with pictures and diagrams, I hope this is of some use. Good Luck!

User Avatar

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

User Avatar

Put an awl in the small hole under nieth of ignition switch,push up, with the ignition in the run position with vehicle off. Pull out in same positon and install new one in the run position.which is same position you will pull out old one.

User Avatar

We are replacing the ignition switch on a 1976 ford F150 Need some help - give us directions

User Avatar

The actual problem is the starter continues to turn after key is turned off and pulled out of ignition.

User Avatar

no. Make sure wiper is in "OFF" position before you turn off your car.

User Avatar

Ignition relay is probably shot. It is in the power distribution block in the motor comprtment.

User Avatar

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

User Avatar

Because the heads of the screws holding the ignition to the column snap off on application you will need a chisel,flat head screwdriver and hammer to make a groove in the head of the screw and unscrew normally.

User Avatar

Well you could ram a flat head into the ignition and turn it to the on position then take steps

User Avatar

TAKE A ALLEN KEY SMALL ONE AND RIGHT UNDER THE SWITCH IS A HOLE PUT IT IN THERE AND TURN THE KEY TO START POSITION AND PUSH THE PIN WIGGEL THE IGNITION SWITCH AROND IT WILL COME OUT

User Avatar

To hookup the solenoid switch on F150 pick-up 5.0 after replacing it, first connect a voltmeter or test light to the solenoid's S terminal. Make sure the starter receives voltage at that terminal when the ignition switch is in the on position.

User Avatar

1986 f150 emisson light on is their restn set

User Avatar

The switch is located on the passenger side kick panel forward of the passenger side door. Hope this helps!

User Avatar

on the ignition switch down by the hazard light control you will see a pin hole turn the lock cylinder to run push a small punch eighth inch iI think may bre smaller.then you will be able to slide the cylinder out may have to pry a little. If you don't have the key you will have to drill the pin out.

User Avatar

how do i find the neutral, or clutch switch on a 2003 ford F150?

User Avatar

the internals of the transmisision is the same should be be able to switch out, but may have to change bell housing on the tranys

User Avatar

turn ignition switch on but dont start. disconnect the negetive battery terminal then reconnect it

User Avatar

Perhaps a bad ignition coil? Perhaps a bad temperature sensor?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.