Unbolt it from the head.
pawl
A ratchet wheel engager is called a PAWL.
The ratchet can turn one way only as the pawl stops it from tuning the other way. :)
Means of controlling rope being payed out.
A pawl and ratchet is used for example in a clock spring winding barrel. A toothed wheel with barbed triangular teeth are cut into the circumference of a metal disc attached to the axle of the spring barrel. This is the ratchet. The pawl is a pivoting teardrop shaped piece of metal mounted on the clock plate adjacent to ratchet. The pawl drops into the gap between the teeth of the ratchet as the clock key turns the spring barrel. The pawl clicks over the teeth until the key turning pressure is removed. The pawl then drops into the last notch in the toothed wheel and stops the spring unwinding.
Pre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure.There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).To change the cable:Disconnect from gearbox end, then unhook from the clutch pedal. Pull the cable through (Engine bay side) then fitting new one is just everything you have done in reverse. You will have to manually release the ratchet pawl (behind the pedal) or you will never get the new cable to fit.
The pawl and ratchet works by the use of a wheel with teeth on it and a brace that stops the wheel from turning in one direction. Then the wheel can be turned and the reversed to tighten or loosed bolts without removing the wrench from the bolt.
Pre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If your reading this article because you have a broken clutch-pedal then please read on.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure. There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).
Pre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If your reading this article because you have a broken clutch-pedal then please read on.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure. There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).
hi its auto adjust,,,you may need a new cablePre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If your reading this article because you have a broken clutch-pedal then please read on.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure. There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).
Pre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If your reading this article because you have a broken clutch-pedal then please read on.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure. There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).
Pre 1997/9 models of Ford Vehicles were self-adjusting via the clutch-foot-pedal. The pedal engages a ratchet system called the QUADRANT & PAWL and is part of the pedal. The mechanism is very similar on older Ford models of: Escort, Fiesta, Sierra, Granada, Transit & others. Newer vehicles may have a Hydraulic Clutch from 1997/9 onwards, and these work differently from the cable & pully mechanism. Clutch-fluid can be bled to improve the ability to operate the clutch, however this is not necessarily a method of adjusting the clutch.If your reading this article because you have a broken clutch-pedal then please read on.If when pressing the foot-pedal it feels like cable is broken, or pedal is loose, ...This is symptomatic of failure of the QUADRANT & PAWL 'ratchet' mechanism due to wear of teeth on the ratchet.In some cases the pedal fails to pull the clutch out far enough to change gear, and may make a 'springing noise'. This is due to slippage on some worn ratchet-teeth, but the mechanism has not reached full failure. There are 2 ways to remedy the fault.1. Change the Quadrant & Pawl, using only genuine Ford parts. #Beware of inferior mouldings that are not up to standard e.g. too soft, and do not trust 'pattern-parts' on eBay etc.2. SHORTEN THE CABLE.Disconnect SPRING ON THE FOOT-PEDAL to release ratchet mechanism.Clamp cable slack (engine end).