How do you change the domelights Map lights on a 2002 Jeep Liberty Limited?

Answer 1

Jeep liberty interior light

(1) Disconnect and isolate the battery negative
cable.
(2) Using a trim stick or another suitable wide
flat-bladed tool, gently pry between the flange
around the edge of the reading lamp housing and the
headliner to release the metal snap clip on each side
of the housing from the mounting bracket above the
headliner (Fig. 14).
(3) Pull the reading lamp away from the headliner
far enough to disconnect the body wire harness connector.
(4) If the vehicle is equipped with an optional
power sunroof, disconnect the body wire harness connector
for the sunroof switch.
(5) Remove the reading lamp from the mounting
hole in the headliner.
INSTALLATION
If the vehicle is equipped with an optional Compass
Mini-Trip Computer (CMTC), the reading lamps
are housed in the overhead console. (Refer to 8 -
ELECTRICAL/OVERHEAD CONSOLE - INSTALLATION).
WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS,
DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTAL
RESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
(1) Position the reading lamp to the mounting hole
in the headliner.
(2) If the vehicle is equipped with an optional
power sunroof, reconnect the body wire harness connector.
(3) Reconnect the body wire harness connector for
the reading lamp.
(4) With the curved corners of the reading lamp
lenses oriented towards the rear of the vehicle, position
the reading lamp housing into the headliner
mounting hole (Fig. 14).
(5) Press upward firmly and evenly on both ends
of the reading lamp until both snap clips are fully
engaged.
(6) Reconnect the battery negative cable

And now the specific instructions on replacing the bulbs. Some of it is duplicated but, that is how the manual explains it.
Jeff

cable.
(2) If the vehicle is not equipped with the optional
Compass Mini-Trip Computer (CMTC), remove the
reading lamp from the headliner mounting hole.
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
INTERIOR/READING LAMP UNIT - REMOVAL). If
the vehicle is equipped with the optional CMTC,
remove the overhead console from the headliner.
(Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE -
REMOVAL).
(3) From the back of the assembly, while pulling
the reading lamp socket away from the outside of the
bulb housing, use a small thin-bladed screwdriver to
release the integral latch tabs of the socket from the
inside of the bulb housing (Fig. 12).
(4) Pull the reading lamp socket and bulb straight
out from the bulb housing.
(5) Pull the reading lamp bulb straight out of the
lamp socket.
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS,
DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTAL
RESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
CAUTION: Always use the correct bulb size and
type for replacement. An incorrect bulb size or type
may overheat and cause damage to the lamp, the
socket and/or the lamp wiring.
(1) Align the base of the reading lamp bulb with
the lamp socket.
(2) Push the reading lamp bulb straight into the
lamp socket until it is firmly seated.
(3) Align the reading lamp socket and bulb with
the mounting hole in the bulb housing (Fig. 12).
(4) Push the reading lamp socket and bulb straight
into the bulb housing until it is firmly seated and the
integral socket latches are engaged within the bulb
housing.
(5) If the vehicle is not equipped with the optional
Compass Mini-Trip Computer (CMTC), reinstall the
reading lamp into the headliner mounting hole.
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
INTERIOR/READING LAMP - INSTALLATION). If
the vehicle is equipped with the optional CMTC,
reinstall the overhead console onto the headliner.
(Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE -
INSTALLATION).
(6) Reconnect the battery negative cable

Reference...


http://www.jeepforum.com/forum/f28/jeep-liberty-interior-lights-510480/


I hope this hep you!