Ford Windstar
Ford Escort
GMC Jimmy
Toyota Tercel

How do you change the front wheel bearings on a 1995 Toyota Tercel?


Top Answer
User Avatar
Wiki User
2011-09-13 00:21:45
2011-09-13 00:21:45

Go to a book store and buy either a CHILTON or a HAYNES manual/repair book for your car's year, make, and model. AUTO ZONE HAS THEM.

These give you step by step illustrated instructions on 100's of repair procedures, ON YOUR CAR. It shows you in the proper order, with pictures, how to take it apart, and how to put it back together, properly.

Most of these books are about $15.00 USD, and are worth every penny.

The only problem here is they do not make an at home repair guide for any Toyota Tercel after 1994. Here is the kicker, every thing about the Tercel changed in 95 so finding info on the Tercel from later years is almost imposible unless you buy a shop owners manual for all Toyota compack models for like $250.

User Avatar

Related Questions

The starter on a 1991 Toyota Tercel is located in the front of the engine. It will be located on the left side.

The timing marks on a 1991 Toyota Tercel are on the crank pulley. They are located on the front of the pulley and under the cam.

can you grease the front wheel bearing s on a 2001 toyota corrolla without removing them. Is there a external greaese fitting.

Yes, drums on the rear, discs on the front.

how do you change front wheel bearing for 420 rancher

The recommended tire pressure for the front and rear tires on a 1996 Tercel are 32 psi. In metric units it is 221 KPa.

When you change rotor or main ball joint, or when they get worn.

I tires are good and balanced properly then look toward front end alignment and wheel bearings.

To change the front wheel bearings on a Ford transit, one needs press or bearing removal tools, as well as a jack. If one does not have these kinds of tools, it is advisable to visit a car mechanic in order to remove the front wheel bearings safely.

are you talking about the front or back? the back bearings are a non serviceable part, the in order to change the bearings u need to change the hub, the front bearings can be separated, but chances are if you have to change your hub, bearings will have to be changed also, you will damage the bearings trying to remove them and put them back in, so my answer is yes. get the parts yourself from and you will save alot of money over dealer or most shops.

the front wheel bearings are a sealed unit, requiring a front hub assembly. when i bought mine it was a dealer item only

How do I change the front breaks on my 2002 Toyota RAV4?

Your front bearings are sealed and are replaced only when they become noisy. A badly worn bearing will roar at speeds above 40mph and will change pitch somewhat as you change from lane to lane due to the side load that is placed on it. Tire noise (due to tires that need rotation) is sometimes mistaken for a worn bearing.

You will need to take the front spindle off and take it to a shop that can press your old bearings off and new ones on.

How do I change the Front Brakes on a 2001 Toyota Corolla?

My front wheel bearings just went in my 04 mountaineer, and we tried to replace them ourselves, but in order to get to the bearings you have to have the truck up on a lift, so unfortunately we had to send it to a mechanic.

Front or rear? Front is very simple, the rear may be a little more complicated.

changing front brake pads on 1991 Toyota truck

The 1993 Toyota coolant temperature sensor can be found on the front of the engine. The coolant temperature sensor will be a few inches above the thermostat housing.

sorry to have to tell you this but the bearings are part of the wheel hub and sealed within. you need to change the entire hub. $$$$$$$

Both the front and rear bearings on a 1998 Cavalier are contained in the hub assembly. The rear hub is attached with four bolts, and the front with three.

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.