The engine has to be raised up a bunch to get the pan off.
Yes. The Bronco body style didn't change again until after 1989.
To repair the head gasket on a 1987 Ford Bronco, the head and the old gasket must be removed. Purchase a new head gasket and carefully install it according to manufacturer specifications.
Follow the link below it will be of GREAT HELP. Hope This Helps.
A 1989 Ford Bronco II has a ( 2.9 liter / 177 cubic inch V6 engine )
I believe that is a ( C6 ) 3 speed automatic transmission with the 351 in a 1989 Ford Bronco
A person can visit a Ford dealership and ask for a 1989 Ford Bronco fuel diagram. Many times the Ford dealers will have mechanics on hand and they can give a customer a copy.
there not that bad a little time and patiants drivers side is a little tite but not bad
can you please provide ma a spark plug wiring diagram for a 1989 ford bronco v6 so i can print it i beleive my wires are on wrong
( .054 inch spark plug gap ) according to fordparts.com for the 5.0 liter / 302 cubic inch V8 engine in a 1989 Ford Bronco
yes you can but I wouldn't recommend it because you will need to make sure all of the old gasket is off or it will just continue to leak
A wiring diagram of a 1989 Bronco 11 fuel pump can be purchased from most auto parts stores. It can also be found in do-it-yourself repair books for a 1989 Bronco 11.
That depends on the size of the engine
if its an automatic, and a four speed, E4OD?
About 4,500 pounds.
take off the wheel and any thng in between you and the pad, open the box for the new pad, read directions.
yes you may have to inter change a few things but they will fit
Passenger footwell outer panel
They were available either with manual or automatic transmissions.
To remove the window in the rear hatch of a 1989 Ford Bronco, the weather stripping around the window will have to be pulled back or pushed down slightly. This can be accomplished with a straight screwdriver or a putty knife.
Sounds like a possible oil pan gasket leak, also check around the oil filter and make sure that it seated properly when it was installed.
It is located under the driver side headlight.
Try the internet
you can fit a 33"x12.5" tire
350 small block No it is not to the guy who answerd up there 350 is GMC. it is a 351 windsor or clevland 5.0 lit. You're both wrong. The engine in a 1989 Ford Bronco II is a 2.9L EFI V6.
The approximate cost to change an oil pan gasket, on your Ford Taurus, is $125. The oil pan gasket can be purchased for $10.
change out the heater core
On the interior firewall to the left of the steering column
Around 2000 dollars
stock 2.9 144 hp
Dana 44 Twin Traction Beam
5x5.5 any rims from a 73-96 f-150,e-150,bronco will fit
You can find the fuse box diagram, for your 1989 Ford Bronco, by taking the fuse box cover off. The diagram of the fuses is on the bottom of the cover.
According to the 1996 Ford Bronco Owner Guide : With engine oil filter change : ( 6.0 U.S. quarts , 10W-30 is the PREFERRED oil for the 5.0 L in a 1996 Ford Bronco )
Make sure that the the two top bolts from the transmission match your engine block before attempting to install. Some are spread out and won;t match.
On a full sized Bronco, it is located in front of the fuel pump between the frame rails near the drivers feet.
The PCM for the 89 Bronco is located on the firewall on the driver side. You can access it from inside the cab, behind the parking brake pedal.
3-5 min drive safe
stock bumper hitch is class 1 @ 2000lbs
In 1989 the 5.8L (351W) made 210-horsepower and 315 pound foot of torque.
how easy is it to change a oil sump gasket on a ford fiesta 1.4 diesel 2008
how do you change out the distributor assembly on a 1989 ford f250
it should some models in that year came standard with a straight six
No there isn't. The Ford Bronco and Ford Bronco II have not sold very well and The Ford Motor Company is not interested on making a Ford Bronco III because of this situation.
IF GAS I NOT SKY HIGH
About 12 city/15 highway with a good running engine.
Measure from center of front axle to center of rear axle.