The oil pump is located on the bottom of the engine. Drain the oil from the oil pan. Remove the oil pan. Remove the oil pump retaining bolts. Reverse the process to install your new oil pump.
The ignition module on a 86 ciara 2.5 is located under hood, center,lower engine area,below driver side of intake manifold . mounted inside of distributor
Is 3030 greater or less than 3300
well first you make sure your car is off. then u take the wires of and undo the bolts then replace it with a new one and the work backwards.
if you are looking to do an engine swap,it is a bad choice, the 3300 is from the 92-93 grand am and does not directly fit. the 3300 is a 90 degree V6 engine like the 3800,you are much better to go with the 3100 that is standard in any V6 grand am from 1994 till 1998. The 3100 is a 60 degree V6, as is the 3.4 engine in the more modern grand am. Even the 3400 could be a difficult job,if you are very mechanically inclined you could do a 3300 swap yourself, but i am told that it is about 100 hours labour to put the 3800 into a grand am and the 3300 would be a very similar job.
It turns out that the fuel injectors were clogged.
1-6-5-4-3-2
where is cam senor on a 91 cutlass ciera 3300
Is the Claias 2.3L 2.5L or 3300?
The ignition module on a 86 ciara 2.5 is located under hood, center,lower engine area,below driver side of intake manifold . mounted inside of distributor
Nov.13/09 my 89 olgs. Just had the same problem, fuel pump is going needs replacing keeps blowing main fuse, try changing fuse under hood, if blows again change pump
It is quite easy to change the thermostat in your 1990 Cutlass. Remove the thermostat housing retaining bolts. Remove the thermostat from the housing. Reverse the process to install the new thermostat.
Air conditioner? Blown fuse Low refrigerant
i have a 90 cutlass ciera with a v6 3300 and just replased that. it is called a combanation sensor. its the crankshaft and cam together located at the back of the harmonic balancer attached to the block. it has 2 bolts on the right side holding it to the block a one in the middle to hold the sensor in place and the sensor sits in it and faces the harmonic balancer on the back of the interrupter rings
Increase of 3300/42 ie 78.6%
There are 18 factor pairs of 3,300: 3300 = 1 x 3300 3300 = 2 x 1650 3300 = 3 x 1100 3300 = 4 x 825 3300 = 5 x 660 3300 = 6 x 550 3300 = 10 x 330 3300 = 11 x 300 3300 = 12 x 275 3300 = 15 x 220 3300 = 20 x 165 3300 = 22 x 150 3300 = 25 x 132 3300 = 30 x 110 3300 = 33 x 100 3300 = 44 x 75 3300 = 50 x 66 3300 = 55 x 60
It is not so much how it affects the sensors themselves, but how much it affects the engine management computer (ECM). The sensors will notice the change in the exhaust gasses and the computer will try to compensate for the change. This often results in poor running, reliability issues, and poor gas mileage. There are however, o2 sensor simulators available aftermarket, though I have no experience with them.
3.3 kg = 3300 g3.3 kg = 3300 g3.3 kg = 3300 g3.3 kg = 3300 g3.3 kg = 3300 g3.3 kg = 3300 g