Oxygen Sensors
Pontiac Sunfire
Mercedes-Benz 190-Series
Honda Accord EX

How do you change the oxygen sensor on 1988 Mercedes 190 E 23?

565758

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 21:11:22
2015-07-15 21:11:22

Located under the passenger side of the car in the exhaust pipe before the catalitic convertor. The wires go through the transmission tunnel and into the loom under the passengers foot well. There is a plastic relay cover panel under the front passengers carpet, remove this to locate the 4 wire connector for the O2 sensor.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The 1988 Toyota oxygen sensor is located on the air cleaner housing. You will find the sensor, on the back side of the housing.

The oxygen sensor in a 1988 Cadillac Deville is located in the exhaust manifold. It constantly monitors oxygen levels in the exhaust to allow the engine to operate and peek efficiency.

If your 1988 Chevrolet Celebrity has the V6 engine the oxygen sensor is in the middle of the exhaust manifold nearest the firewall. If you have the 4 cylinder engine the oxygen sensor is located in the exhaust manifold just above the exhaust pipe flange.

It is about $118.00 for one, plugging in the oxygen sensor isn't so bad, but the plug itself goes up into the frame of the car and seems to dissappear somewhere inside the car. Im having trouble finding this myself.

I'm not a mechanic / technician but on a 1988 Ford Ranger there might be ( 1 ) oxygen sensor ( upstream sensor )

The oxygen sensor on a 1988 Honda Prelude fuel injected engine is on the exhaust manifold. It screws directly onto the front of the exhaust manifold.

Chiltons auto manuals have good diagrams, your oxygen sensor is on your exhaust in front of the catalytic converter.

A 1988 Jeep Cherokee has one oxygen sensor.

oxygen sensors are on the exhaust pipe close to the engine. Some are on the exhaust manifold. some may have an upstream and a down stream sensor.

On top of the exhaust manifold on the drivers side.

they're usually after the cat-con on the exhaust...

The oxygen sensor on a 1988 Astrovan is located in the exhaust system. There are two oxygen sensors, one on the driver's side and one on the passenger side of the exhaust.

The oxygen sensor on the 1988 ford 2.9 liter engine is located on the exhaust pipe just behind the right exhaust manifold. It screws into the exhaust pipe and has a small wire running to the tip of it. Just unplug the wire and turn out the sensor with a wrench.

Camshaft position is taken from the distributor, there is no separate sensor.

Mercedes Benz did not manufacture a model with that designation in 1988.

crank position sensor is between oil filter and starter, follow wire from module

in the exhaust manifold right before the catalytic converter

Rear of engine follow exhaust manifold at rear of motor(closest to firewall) you will see oxygen sensor there.Simple to remove(1 only on this motor)

There should be a connector under the car that it plugs into. It then goes to the computor.

There are two. They are in the exhaust system. One is before and one is after the catalytic converter.

Its black/purple depanding but just one single wire

the oxygen sensor is grounded when you thread it into the exhaust manifold the oxygen sensor should have only 1 wire it should be purple the didnt start putting 2 or 4 wire sensors in until the early 90's there should be a ground from the battery to the block

Should be right before the catalytic converter. Mine is a 1988 and that's where it's at.

Located on the back side of the front license plate holder. Pencil shaped with a long black wire.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.