Serpentine Belts
Jeep Cherokee

How do you change the serpentine belt on a 1998 Jeep Cherokee classic?

171819

Top Answer
User Avatar
Wiki User
2011-12-15 23:05:51
2011-12-15 23:05:51

Just loosen the power steering pump. Pump swing on the bracket just loosen the bolts on the swing points and under the pump there is a adjustment boldto tighten on loosen the belt. Be sure you draw the belt diogram on paper because it can turn in a night mare

oh man, then you brake out the broom handle and tighten back up, like when you were a kid, and changed a rear tire on your bike... WRONG....

There is a tentioner pulley under the power steering pump, 10mm socket, goes on the top left side of tens pulley, loosen it, the use a 15mm wrench to loosen the bolt that holds said pulley on, draw belt pattern 1st....remove old belt, replace, and reverse the removal pattern... good luck.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Th e automatic transmission in a 1998 Jeep Cherokee, not a Grand Cherokee, is an AW4.

User Avatar

There is a 15mm. bolt (long bolt) that adjusts the tension of the serpentine belt. It is in the area of the power steering pump, just left and down. Either draw a map, or look on the front of the engine compartment to see how the belt is routed around the pulleys.

User Avatar

can you give me instructions on changing the water pump on a 1998 jeep classic 4.0.

User Avatar

You can change the serpentine belt by loosening the tensioner pulley. When the tensioner pulley is loose and the serpentine belt will become loose. Put the new serpentine belt on and tighten the tensioner pulley.

User Avatar

How do I change a headlight bulb on a 1998 jeep grand cherokee?

User Avatar

"how do you change a throttle position sensor on a 1998 jeep grand Cherokee?" could someone without any experience do it?

User Avatar

The 1998 Camry did not have a serpentine belt. Do you have a 1998 Corolla?

User Avatar

How do you route the serpentine belt for a 1998 w

User Avatar

No, too many were produced and it is not a limited production vehicle like the 1998 Jeep Grand Cherokee 5.9 or the SRT.

User Avatar

loosen the bolt. There should be a sticker with a diagram under the hood.

User Avatar

It can be as easy as replacing a fuse or you may have to buy and install new switches

User Avatar

The only differences are between a regular Cherokee and a Grand Cherokee.

User Avatar

yes but change your 98 intake manifold and injection to the new engine

User Avatar

Don't know where you can download, but I know you can buy a manual off eBay for under $10.

User Avatar

Blower resistor is under the glove box. It is diamond shaped with 2 screws holding it in.

User Avatar

You have to unscrew the tensioner bolt and remove the serpentine belt first, then change the pulley and replace the belt.

User Avatar

diagram of serpentine belt for 528i BMW

User Avatar

where can i get a diagram for a serpentine tensioner belt for a 1998 Oldsmobile bravada

User Avatar

I am trying to save myself some money and I want to change the serpentine belt on my 1998 ford contour 2 L manual transmission....any ideas out there I would really appreciate any advice.

User Avatar

i don't know if this will help you, but it helped me. http://www.zx2racing.com/pages/mods/pulley_dia.htm

User Avatar

A 1998 Jeep Cherokee has disc brakes in the front.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.