Dodge Durango

How do you change the tail light assembly on a 1999 Dodge Durango?

596061

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 21:13:56
2015-07-15 21:13:56

Raise the lift gate and look on the backside of the taillights. There are 2 phillip screwheads. Remove those screws, pull the light slightly toward the outside of the vehicle, and pull out. When you reinstall them. Insert the tab on the light into the hole which is to the outside of the vehicle and put back in place and reinstall screws. This procedure takes about 5-10 minutes.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The taillights are an assembly. The lens covers can not be replaced separately

Change the sensor located on rear-end housing

you need to remove the small screw on the park /turn assembly from the front. then you have access to the 2 bolts on the bottom of the h/light then two higher up on either side.Ron

The rear, 2 screws and the tail light comes out. The front, there's a small T15 torx screw under the headlight. Then just pull the signal assembly straight out.

From outside,take a screws out to get light assembly loose and remove light socket from back of assembly and channge your light bulb,then put it back.

you have to remove the headlight assembly 3little bolts

on all dodge trucks the way you change the bulbs is simply unscerew the tail light assembly and remove it from the rear of the vehicle and you will see your lightbulb fittings right on the back of the light assembly

Your Dodge Durango may stall when idling at a stop light for a couple of reason. One reason may be that a part needs to be replaced on the car.

you don't because it does not have a light in it, or you can use magic. I'm confused, the Owner's Manual states Replacement Bulb Ash Tray Bulb No. 161. I checked parts replacement and found: Wagner Lighting - Ash Tray Light Bulb Fits Your 2001 Dodge Durango

To replace the brake light on a 2001 Dodge Durango the light lens must be removed. It is held on by a clip on one side and a hinge on another. It opens like a door to access the brake light housing.

4x4 dash lights on a Dodge Durango don't work

Pull the switch and change bulb in rear. 1 for night light and 2nd for fog light indicator.

On my 2005 Dodge Ram Daytona. I had to open the tail gate, remove the two screws on the jam next to the light assembly. After removing the assembly, there is a light bar held by six screws. After removal of these, you can select the bulb you wish to change and then reassemble to install light assembly.

I believe it is 2 torx screws inside the tailgate holding the assembly. Have to replace the whole assembly.

The fuses on the 2000 Dodge Durango should be labeled for each part such as the tail lights. The tail light fuse is a 30 A.

What causes ticking, check engine light, and the check gauges sensor to come on in a 1999 Dodge Durango 5.2L SUV?

Turn the key on, engine off, press the gas pedal to the floor three times. cycle key and light should be off.

There are three black caps that screw off in the trunk behind the brake light itself unscrew them and the assembly comes out then change bulb

then you need to stop flicking the light switch

For the rear plate yes, but not the front one.

door open light is on, locks and mirrors will not work

To change your Durango's tail light, first make sure to have a flat head screw driver and a new bulb. You will then open your trunk and remove the screws to the tail light, swap out the bulbs and replace the housing case.

The tail light is an assembly. The lens is not removable. To replace a bulb you remove the assembly by opening the liftgate, removing two fasteners, and pulling the light rearward.

Buy or borrow a code scanner to find out what the code is then you'll know for sure.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.